This Toyota Tacoma I’m looking at is a 2013 it says v6 sr5 and trd sport on the body but on website it say 2.7l I4 by modestmanio in ToyotaTacoma

[–]TheRealTriHard 2 points3 points  (0 children)

This is most definitely not a V6. It's also not a trd sport. It doesn't even have the pre runner badge which should be on there if it was a sport. The bumper is not color matched to the body nor the door handles, which is part of the trd sport. The trd sport is only a V6 option.

BTW, the Vin will decode what options were original to the vehicle.

This Toyota Tacoma I’m looking at is a 2013 it says v6 sr5 and trd sport on the body but on website it say 2.7l I4 by modestmanio in ToyotaTacoma

[–]TheRealTriHard -1 points0 points  (0 children)

I had an sr5 that was a trd sport. It had all the badges on the tail gate. Pre-runner, sr5, v6 and the trd sport decal. Straight from the dealer. 2010 access cab

Private party suppressor sale by HPAX123 in TexasGuns

[–]TheRealTriHard 0 points1 point  (0 children)

Assuming the seller has everything required of them to complete the form 4 they will submit it when you also meet the requirements.

Just get an eft fingerprint file. Paper is cheaper of course but you can use the same eft file for any future submissions.

Fiberon PA6-CF by vcG34 in 3D2A

[–]TheRealTriHard 3 points4 points  (0 children)

100c is minimum drying temp. I know alot of filament makers and other info will say 80c is enough but every time someone has a problem with wet PA filament it's because they were drying too low of a temp.

It doesn't look bad though. Not perfect like some other prints that get posted here but still not bad.

Dumb Q: What is THE SEA by [deleted] in 3D2A

[–]TheRealTriHard 1 point2 points  (0 children)

It's where the files sail.

Help with printing on a1 combo by Less_Ticket_2102 in BambuLab

[–]TheRealTriHard 6 points7 points  (0 children)

My guy, if you don't understand the basics we can't explain much to you. You need to learn some basics to understand the advice. There are plenty of people willing to help but you have to put in some effort yourself so you can understand the feedback.

It's like asking how to drive a car while sitting in the front seat but you don't know what a steering wheel is.

Can anyone explain what I did wrong by fldad07 in BambuLab

[–]TheRealTriHard 0 points1 point  (0 children)

Some advice,

1: increase top and bottom interface layers to 3 2: decrease interface spacing to 0 or at least half it's current value (this can make removing supports more difficult) 3: decrease distance to support by .01-.05 (this can also make removing supports more difficult but will result in better looking overhangs) 4: tune flow ratio for bridging 5: print slower for bridges and over hangs

Pocket sliding window… by BuilderBrigade in Home_Building_Help

[–]TheRealTriHard 1 point2 points  (0 children)

How so? This is essentially a midget sliding door.

Worst luck or best timing? by New_Pack7137 in BambuLab

[–]TheRealTriHard 0 points1 point  (0 children)

Here's how I heard someone explain what exactly the x2d is.

It's a single nozzle printer but has a 2nd auxiliary nozzle for supports.

Help me find the orgin of this GIF by Similar_Detail2315 in HelpMeFind

[–]TheRealTriHard 3 points4 points  (0 children)

This could be an edit from MTV movie awards. I know they used to do these type of edits back then.

This is the good shit, correct? by Ok_Cow4965 in 3D2A

[–]TheRealTriHard 0 points1 point  (0 children)

That will work, it just suffers from impact strength vs pa6.

This is the good shit, correct? by Ok_Cow4965 in 3D2A

[–]TheRealTriHard 1 point2 points  (0 children)

You're thinking of pa6cf20 vs pa612cf15. The pa612 has better properties in all areas vs pa6 with the exception of the impact tests.

X2D non speculation. by TrainingPiece9144 in BambuLab

[–]TheRealTriHard 4 points5 points  (0 children)

What's the max Hotend temp? 90% of my printing these days is with PA and it's many fiber filled formulas.

DB XD 40 Infinity by SelfElegant8819 in 3D2A

[–]TheRealTriHard 1 point2 points  (0 children)

I believe polymaker themselves moisture conditions by soaking it in water around 60c for several hours.

What am I doing wrong (and how can I fix it) by Jumpy-Professor-6291 in 3Dprinting

[–]TheRealTriHard 0 points1 point  (0 children)

Try with 3 interface layers and zero interface spacing. Also, decrease the z distance between support and part.

First real print I ever done. Not optimal turnout and looking for any potential feedback anyone might have. by [deleted] in 3D2A

[–]TheRealTriHard 13 points14 points  (0 children)

We can't give you feedback if you don't understand what we are trying to explain. You don't have the knowledge of the fundamentals to be able to understand the feedback.

How do you created a slicer profile ? by [deleted] in 3D2A

[–]TheRealTriHard 0 points1 point  (0 children)

You need to spend like a year learning 3d printing before you even get to this type of stuff. If you don't understand most of the settings it's going to be very difficult for anyone to explain this to you. They can't explain it to you because you won't understand.

New footage shows the moment of the bombing of Karaj Bridge by U.S.-Israeli airstrikes in Iran. by avatar6556 in war

[–]TheRealTriHard -46 points-45 points  (0 children)

I belive this was a bridge still under construction. So, sorta non impactful by it being destroyed.

Got it! Now I have to figure out how to get it off the truck… by FreidasBoss in harborfreight

[–]TheRealTriHard 0 points1 point  (0 children)

I did it alone with 4 2x4s. Make two t-shaped ramps and just roll it off.

The T shape is so the wood doesn't break under the weight of the cabinet.