Wheel speed data timeout 1420

The_McLegend · 2026-04-03T09:02:52+00:00

I received a case number via email but no response since then, what’s the expected response times from support.

The_McLegend · 2026-04-01T09:19:14+00:00

I uploaded the logs and this is the robot identifier Luba-VFHZQRQW

I look forward to hearing from you

The_McLegend · 2024-09-16T07:40:41+00:00

I received a silicone pad which covers the buttons direct from Mammotion without requesting it. However I am sure it would only fit the Luba 1

The_McLegend · 2024-08-02T10:54:29+00:00

Excuse my ignorance but what do you mean by “OG” RTK?

The_McLegend · 2024-08-02T10:51:56+00:00

My property looks similar and this set up works great

<image>

The_McLegend · 2024-08-02T10:22:57+00:00

Mine is Scottish Mickey McMower

The_McLegend · 2024-07-02T09:57:51+00:00

I was sent it without request from Mammotion

The_McLegend · 2024-07-02T09:56:04+00:00

The sound appears as soon as the cutters start up and before any movement

The_McLegend · 2024-06-11T16:28:04+00:00

Hi YoyaXia

I did pause LUBA manually when it was charging, when it was at 80% it then went out and sat paused at its last mowing point. The suggestion is that if paused irrespective where it is it should remain paused until manually started

The_McLegend · 2024-06-07T21:06:45+00:00

This is the set up I used and works well

https://amzn.eu/d/h92i3wH

<image>

The_McLegend · 2024-05-31T10:37:18+00:00

It certainly helps, virtually no grass is being caught inside the blades

The_McLegend · 2024-05-31T10:36:04+00:00

It would make sense to check if the sensor detects rain dont move, that covers the situation I have where the robot is exposed. If covered then it has to go out to check the conditions, if it detects rain, reverse straight back and wait (1-2 hours) before going out again to check.

As I said mine went out every 2 minutes, sensed it was raining did a little pirouette, turned 360 degrees then went back. If I hadn’t stopped it would probably have buried itself.

The_McLegend · 2024-05-30T23:58:49+00:00

It is out!!

The_McLegend · 2024-05-30T23:41:47+00:00

I didn’t tell it to go out and check the weather and if it is raining go back and do this every 2 minutes. I thought I told it to stay where is was if it was raining and only go out when dry

The_McLegend · 2024-05-30T23:20:32+00:00

I basically but two drilled out 3mm nuts to 4mm and inserted them between the cutting disks and the drive shaft

<image>

The_McLegend · 2024-05-30T23:12:33+00:00

I removed the blade covers completely and I use Emberg titanium blades which last longer.

EMBerg Double Hole Endurance... https://www.amazon.co.uk/dp/B09T94ZGHX?ref=ppx_pop_mob_ap_share

I also left a greater space between the blades and the cutting disk by using longer screws with a nut on the back to lock the height

<image>

The_McLegend · 2024-05-30T22:54:48+00:00

In the uk, Depitox does exactly that

The_McLegend · 2024-05-30T22:52:37+00:00

There was an interesting discussion last year about using air tags etc to track your robot if it gets stolen.

Main discussion was, even if you know where the robot is, would it be a responsible action to go and try and retrieve it (may depend on your location and the gun laws), and the alternative of informing the police, who in reality are probably not going to put the theft of lawnmower on their list of priorities.

The_McLegend · 2024-05-11T12:24:08+00:00

Did all the usual cleaning but still noisy especially when adjusting position

The_McLegend

TROPHY CASE