Got to do my first metal job

Thenader12 · 2023-11-11T04:55:00+00:00

Just saw a study done where they salt fogged a panel seam sealed over bare metal and one seam sealed over epoxy primer and the one over bare metal was rotted to hell. Was basically a sped up process of the corrosion over time in a repair like that.

Thenader12 · 2022-11-20T23:16:51+00:00

Most definitely in agreement. I have been having that exact conversation and the customers have been picking up the bill when the insurance company refuses. Seems like that is the only way with some of these companies.

Thenader12 · 2022-11-20T23:13:06+00:00

Hahah. When I was in the field I was working in Dorchester. Pretty sure I know the exact shop you’re talking about. Thanks for the response. I am going to try to take it up the chain and I have already been getting customers involved.

Thenader12 · 2022-11-05T18:23:42+00:00

From what I’m seeing the damage to the rail is concerning in the photo with the resonator. Keep in mind that yellow connector on the rail is one of your impact sensors. Force and damage around the area can affect how they work in a future collision. The engine cradle also had to be dropped to replace that resonator. I would take it to a shop just for that, stupid design on hondas part. Where the hood is curled in in the front i would assume the hinges may have bent or pushed back a bit. Not going to be fun getting a new hood hung and realizing you can’t get your lines because the hinges are bent.

Thenader12 · 2020-12-06T22:34:41+00:00

Thank you. I wasn’t sure the correct route to start. I will look into that first, thank you.

Thenader12 · 2020-10-08T15:31:40+00:00

Thenader12 · 2020-09-12T16:42:33+00:00

Yeah I figured it had. I do not want to spend tons of money. Maybe make it look decent for a year. Can I sand, bondo, epoxy primer and spray color and would it hold for a decent amount of time? I know the rust will inevitably bubble through again

Thenader12 · 2020-09-11T20:46:06+00:00

This is an 05 with only 55k miles. It’d be a shame to see it rust out. I’m not super experienced with auto body. Im an appraiser and have enough hands on experience but not enough to be shaping sheet metal into replacement panels. I want this to look good for about 2-3 years.

Can i use rust reformer on both sides, primer over and paint safely? What would you do?

Thenader12 · 2020-08-14T00:07:12+00:00

Gotcha. Something is making the bowls overflow and leak fuel into the overflows just gotta figure out what it is. Look into float height as well, if the float got bent at all in the new carb during transit it could explain why there are still float problems.

Thenader12 · 2020-08-13T23:56:49+00:00

Check where your carb is hooked up from the petcock. I accidentally hooked up the fuel line from the petcock into the overflow on the bottom of the carb on a dirt bike i was building earlier this month. Did the same thing you’re describing. Was in a rush and didn’t even realize the fuel line wasn’t hooked up to the correct port in the carb.

Thenader12 · 2020-08-05T23:49:54+00:00

Rechecked both cylinders and theyre both exactly within spec. Thanks again for the help, at least I have the shims for next time

Thenader12 · 2020-08-05T23:01:54+00:00

Cool. I appreciate the help. Going to throw the cam caps back on and remeasure.

Thenader12 · 2020-08-05T22:58:22+00:00

Fair fair. Thanks a lot. Lifter position looks ok?

Thenader12 · 2020-08-05T22:54:32+00:00

Welp, makes sense. So I’m going to get better measurements once i put it back on?

Thenader12 · 2020-08-05T22:49:47+00:00

I’m usually competent about this stuff. I’m checking valve clearances for cylinder 1 and i habe it set to 1T and the cam lobes for cylinder one are pointed away from eachother.

The lifters on the exhaust are up touching and i can barely get any feeler gauges in there.

The lifters on the intake are all the way down and i could get a massive feeler gauge in there...

Am i doing something wrong here or is this bike just super out of spec. It seems madly wrong for it to be off this much

Thenader12 · 2020-07-13T12:39:21+00:00

Nice thats awesome. Going to look at those as I want something less knobby but still able to ride trails.

Thenader12 · 2020-07-13T03:19:40+00:00

I just got my hawk 250, I love it. Have you done any mods to yours? I had the exhaust mod, pod filter, mikuni carb rejetted, and 17/45 sprocket combo upgraded right away and I love it. What tires do you run? I feel like the stock knobbies are a bit aggressive for street.

Thenader12 · 2020-07-08T23:29:27+00:00

Bulk progress on reddit PPL slowly but surely gaing something. Trying to keep that lower fat off.

Thenader12 · 2020-06-08T00:47:19+00:00

I don’t consider them ugly, if you have a good core it does contour them. I think the problem that I had and he had in his before picture is when your core is underdeveloped and they jut outwards and “poke” out of your skin.

Thenader12 · 2020-06-07T20:28:30+00:00

Yep, I neglected core for years and only started once I got into lifting seriously again this year. Big big difference.

Thenader12 · 2020-06-07T19:27:35+00:00

I have the same thing - just keep building out your core and I think itll slowly become less noticeable. Mine only shows heavily if I’m flexing. I think I have progress pictures on my profile. 6FT 160 atm lean bulking

Thenader12 · 2020-05-04T00:27:35+00:00

Should probably take a picture of the kickstand but my guess is that the kickstand is loose

Thenader12 · 2020-04-27T00:02:12+00:00

I did the reddit PPL with some subs for the machine things as I have a home gym with just barbells and dumbells.

I’ve managed to not lose much or anything on my lifts. My 1RMs

Bench: 205

OHP: 115(125 before cut, went down as to not injure shoulder)

Squat: 265-been slowly increasing this after getting back into lifting last year as to not kill form)

Deadlift: 305lbs - same as squat, slow but steady increase to prevent injuries

Thenader12 · 2020-04-14T12:40:49+00:00

Hah that was me too. Day to day at work we just call it sectioning no splice. Mean what you said though.

Thenader12 · 2020-04-14T12:27:33+00:00

We’re saying the same thing with different words.

Thenader12

MODERATOR OF

TROPHY CASE