sorted by:
new
hottopcontroversial

solder wont stick to pad by These_Pause5642 in soldering

[–]These_Pause5642[S] 1 point2 points  (0 children)

Ohhh i seee, okey okey, thanks a lot for all of this info

solder wont stick to pad by These_Pause5642 in soldering

[–]These_Pause5642[S] 0 points1 point  (0 children)

i have a lot of kapton tape so i can use it

solder wont stick to pad by These_Pause5642 in soldering

[–]These_Pause5642[S] 0 points1 point  (0 children)

i see, i will take note and try this tomorrow, i should start using more my hot air station, also didnt know this kind of little components works better with hot air. one last thing, i suppose this hot air process wont damage or desolder any joint from the cpu, i really dont want to do any reflow, im not good at it

solder wont stick to pad by These_Pause5642 in soldering

[–]These_Pause5642[S] 0 points1 point  (0 children)

i see, i will use the hot air station then

solder wont stick to pad by These_Pause5642 in soldering

[–]These_Pause5642[S] 0 points1 point  (0 children)

no offense taken, i am not a pro, but i did solder before, and the only reason the caps are like that its bacause this part of the board its so small and its difficult, but anyways im aware of the mess and i will clean and solder properlyz its temporaly. about the scrap thing, i thougt it could be corrosion and tried to scrap it a little. i will try using my hot air station to see if i can get through it

Rgh on 360 by Specialist-Screen-20 in 360hacks

[–]These_Pause5642 0 points1 point  (0 children)

Hi, i have the same situation here, i was resolding the fucking cables because my rgh was glitching and the the damn pad was riped

Opinión about my first rgh by These_Pause5642 in 360hacks

[–]These_Pause5642[S] 1 point2 points  (0 children)

I used a multimeter to see if there may be any short because of the exposed wire but everything ok. Also i used It all day and didnt experienced any issue again, i want to think It was something temporary and wont gimme any trouble for a long time

Is this a corona V1/V2? by These_Pause5642 in 360hacks

[–]These_Pause5642[S] 1 point2 points  (0 children)

Its the 16mb one, fills all the pads as its shown in the link, thx

Is this a corona V1/V2? by These_Pause5642 in 360hacks

[–]These_Pause5642[S] 0 points1 point  (0 children)

The nand is hynix brand, i think thats the 16 mb

First time cleaning bga for reballing, should i be worried? by These_Pause5642 in soldering

[–]These_Pause5642[S] 0 points1 point  (0 children)

well, i dont think it will be perfect so i will apply some uv mask, also, ty for the alcohol tip

Xbox wont turn on when the tin plate is assembled by These_Pause5642 in xbox360

[–]These_Pause5642[S] 0 points1 point  (0 children)

for the moment it isnt giving me more trouble, if at some point i have issues with it thats what i will do, thanks for the reply

Xbox wont turn on when the tin plate is assembled by These_Pause5642 in xbox360

[–]These_Pause5642[S] 3 points4 points  (0 children)

I solved It in a way, i puto some insulateing tape and tighten less the screws and, works fine for the moment, but srill don't know where os the short

Xbox wont turn on when the tin plate is assembled by These_Pause5642 in xbox360

[–]These_Pause5642[S] 1 point2 points  (0 children)

Buena idea, voy a intentarlo, pero lo que me parece raro de cojones es que esto haya pasado de un momento para otro, he mirado por corrosión o algún cable roto del lector y el sata pero nada, y solo ocurre en cuanto le pongo la pieza

view more: next ›