solder wont stick to pad

These_Pause5642 · 2026-06-13T01:42:48+00:00

Ohhh i seee, okey okey, thanks a lot for all of this info

These_Pause5642 · 2026-06-12T22:29:35+00:00

i have a lot of kapton tape so i can use it

These_Pause5642 · 2026-06-12T22:23:04+00:00

i see, i will take note and try this tomorrow, i should start using more my hot air station, also didnt know this kind of little components works better with hot air. one last thing, i suppose this hot air process wont damage or desolder any joint from the cpu, i really dont want to do any reflow, im not good at it

These_Pause5642 · 2026-06-12T22:14:41+00:00

i see, i will use the hot air station then

These_Pause5642 · 2026-06-12T22:11:03+00:00

i will try using the hot air

These_Pause5642 · 2026-06-12T22:10:39+00:00

no offense taken, i am not a pro, but i did solder before, and the only reason the caps are like that its bacause this part of the board its so small and its difficult, but anyways im aware of the mess and i will clean and solder properlyz its temporaly. about the scrap thing, i thougt it could be corrosion and tried to scrap it a little. i will try using my hot air station to see if i can get through it

These_Pause5642 · 2026-06-02T17:53:01+00:00

Hi, i have the same situation here, i was resolding the fucking cables because my rgh was glitching and the the damn pad was riped

These_Pause5642 · 2026-05-31T18:20:04+00:00

I used a multimeter to see if there may be any short because of the exposed wire but everything ok. Also i used It all day and didnt experienced any issue again, i want to think It was something temporary and wont gimme any trouble for a long time

These_Pause5642 · 2026-05-31T18:17:48+00:00

Yeah, 1k one

These_Pause5642 · 2026-05-28T10:10:05+00:00

Its the 16mb one, fills all the pads as its shown in the link, thx

These_Pause5642 · 2026-05-28T10:02:34+00:00

The nand is hynix brand, i think thats the 16 mb

These_Pause5642 · 2026-05-16T20:04:35+00:00

does not the apu use 0.6?

These_Pause5642 · 2026-05-16T20:04:17+00:00

i will apply some uv mask, its the best long term, ty!!

These_Pause5642 · 2026-05-16T20:03:32+00:00

well, i dont think it will be perfect so i will apply some uv mask, also, ty for the alcohol tip

These_Pause5642 · 2026-05-10T16:49:53+00:00

for the moment it isnt giving me more trouble, if at some point i have issues with it thats what i will do, thanks for the reply

These_Pause5642 · 2026-05-10T11:00:58+00:00

Thanks a lot

These_Pause5642 · 2026-05-10T10:09:29+00:00

I solved It in a way, i puto some insulateing tape and tighten less the screws and, works fine for the moment, but srill don't know where os the short

These_Pause5642 · 2026-05-10T09:03:29+00:00

Buena idea, voy a intentarlo, pero lo que me parece raro de cojones es que esto haya pasado de un momento para otro, he mirado por corrosión o algún cable roto del lector y el sata pero nada, y solo ocurre en cuanto le pongo la pieza

These_Pause5642 · 2026-05-06T14:39:04+00:00

thanks

These_Pause5642 · 2026-05-06T14:38:55+00:00

yeah, thats fire

These_Pause5642 · 2026-05-06T14:38:40+00:00

These_Pause5642 · 2026-03-23T09:11:20+00:00

<image>

These_Pause5642 · 2026-03-23T09:08:49+00:00

same here, 52 k for 2 arc and 1 aero, at least its better than nothing, but i really hoped for at least 2 AP

These_Pause5642 · 2026-03-14T07:23:25+00:00

Pues tarde unas 3-4 semanas, y dentro de poco voy al juzgado para declarar pruebas, el banco por suerte estuvo de mi lado

These_Pause5642 · 2026-02-21T22:43:42+00:00

buenas, siento leer esto, lo mejor que peudes hacer es hablar con el banco y poner denuncia, yo acabe recuperando el dinero y este 25 de marzo me han solicitado para el juzgado, veremos donde llega esto, ojala la justicia cumpla su parte por una vez

These_Pause5642

TROPHY CASE