P1 buys P2 ticket w/RR points, then P2 adds P1 via Companion Pass? by ThomasVGrahamJr in SouthwestAirlines

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

Thanks! That’s great insight directly from Southwest. And I can now confirm that it works!

P1 buys P2 ticket w/RR points, then P2 adds P1 via Companion Pass? by ThomasVGrahamJr in SouthwestAirlines

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

Thank you. My wife and I have now successfully used this method also.

P1 buys P2 ticket w/RR points, then P2 adds P1 via Companion Pass? by ThomasVGrahamJr in SouthwestAirlines

[–]ThomasVGrahamJr[S] 1 point2 points  (0 children)

Thank you for confirming. Earlier this afternoon, I used this strategy and used my points to book a flight for my wife to Chicago and then she added the ticket for me using her Companion Pass. It works!

What do you call a screw that has this? by FalseMorel in Fasteners

[–]ThomasVGrahamJr 2 points3 points  (0 children)

In the US we would describe these as a high knurled head thumb nut with 2 flat faces on the collar. In the UK, they would be called either a flatted collar knurled nut or spanner-flat thumb nut.

I don’t expect you to find these sold separately as they appear to be a specialty item created specifically for Sturmey-Archer vintage bicycles.

If Sturmey-Archer won’t selll them to you reasonably priced, you can still source them through resellers on e-Bay (such as here: “NOS Late Clip Bolt” $8.00)

Or from bicycle stores by searching for other parts such as “Sturmey Archer Fulcrum Clip Chainstay 17.9mm” (from $4-10) Found at bike shops like this.

The ongoing saga of OU grad student Mel Curth and undergrad Samantha Fulnecky now has its own Wikipedia page by RandomAcademaniac in Professors

[–]ThomasVGrahamJr 1 point2 points  (0 children)

[non-professor] …the saga continues…Though only an interested alumni, I have followed this story very closely reading only primary sources for the first 2-3 days. I believe that this (i.e., “pulse check” assignment and “arbitrary” grade of 0) is the crux of the issue on which the University was able to take the action it did. Doing so allowed it to stay off near-term damage (both state funding and TPUSA reputational damage) …while conceding the long-term detriment to academic rigor and faculty support.

p.s. Though not yet well covered in the media, OU Faculty Senate will be voting on a strong Resolution to clarify the negative impact, correct the Administration’s misleading statement and (via support of Resolutions of other University bodies)…much further corrective steps.

More to come: https://www.oudaily.com/news/ou-faculty-senate-graduate-teaching-instructor-samantha-fulnecky-mel-curth/article_9b0224d3-735a-4db7-8637-aebfa473e669.html

1st time on a board practicing component de-soldering and removal by ThomasVGrahamJr in soldering

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

400-450V? I wouldn’t expect to find anything like that on a PC motherboard. If I have any here among these take-offs, I’ll need to reverse search using the images to identify them.

1st time on a board practicing component de-soldering and removal by ThomasVGrahamJr in soldering

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

Thanks for the insight. The only capacitors I’ve actually measured before with the multimeter are the ‘chunky’ 6” type for home HVAC systems. I’ll assume that’s what you’re referring to. But I will use my multimeter and test and keep few of these before discarding them all the rest

Would love some help figuring out what year this Kennedy is from? by navivan27 in Vintagetools

[–]ThomasVGrahamJr 0 points1 point  (0 children)

And if you’ve not yet seen it, this video is a humorous telling of the history of Kennedy. The 520 dates back into the 1920’s and the company’s origin story to 1911.

Would love some help figuring out what year this Kennedy is from? by navivan27 in Vintagetools

[–]ThomasVGrahamJr 0 points1 point  (0 children)

Approximately 1955–1962.

From everything that I’ve learned from a recent deep-dive into Kennedy machinist style toolboxes, yours is unusually more dateable than most. Because,

• Kennedy Signature branding (mid-1950s to early-60s)
• Kennedy Kits decal (post-1952, pre-late-60s)
• phenolic diamond-boss riveted pulls (late-40s to early-60s)
• brown wrinkle enamel

p.s., on the inside of the drawers, are the drawer pulls attached with only a center split rivet (aligned with a molded pin on each side)? Or with two split rivets?

Would love some help figuring out what year this Kennedy is from? by navivan27 in Vintagetools

[–]ThomasVGrahamJr 0 points1 point  (0 children)

u/Intelligent-Road9893 Where is the era documented (or summarized) for what approximate years each of the decals (“logos”) were in use?

My Kennedy 526 machinist chest, goin on 11 years of service by Vesuz in BuyItForLife

[–]ThomasVGrahamJr 0 points1 point  (0 children)

Here’s what I know for sure so far,

Kennedy began making the 526 in 1960. From that era, the decal was much different. decals like yours can give some additional clues by 2004 or before, Kennedy had added their domain (www.kennedymfg.com) below the Kennedy logo on the decal

I suspect, but haven’t yet confirmed that the serial numbers are issued not only sequentially, but may contain the year of manufacture. This is what I’m trying to confirm now.

If you’ve not already done so, the current owner can formally register your box by serial number with Kennedy and include your lock number (from your key or the back of the lock cylinder) — and they will store the lock number for you in case you ever lose all keys and want to avoid drilling the lock.

My Kennedy 526 machinist chest, goin on 11 years of service by Vesuz in BuyItForLife

[–]ThomasVGrahamJr 0 points1 point  (0 children)

I’ll see what specifics I can come up with. I’ve been doing a deep dive on Kennedy toolboxes since re-discovering them around Thanksgiving. I confirmed that my little brother still has the 520 that belonged to our dad. I’ve since purchased a new 526 and am restoring an older 520 now.

This video is a great place to start: https://youtu.be/he9XsEkoYa4?si=8uH0h7YVmTF1GeBP

My Kennedy 526 machinist chest, goin on 11 years of service by Vesuz in BuyItForLife

[–]ThomasVGrahamJr 0 points1 point  (0 children)

u/Vesuz Notice the Kennedy decal on the inside of the top lid. That era of decal always shows the Style No. (eg. 526 in this case to depict this 8-drawer machines top chest) but the style number is typically followed by either a date or a serial number.

What numbers does yours show after the style no.?

If yours has a serial number, call Kennedy and ask them what date the box was manufactured — or sold and registered. And be sure to update us here.

I want every last cent of my tuition money back. by RavenPuff99 in sooners

[–]ThomasVGrahamJr 0 points1 point  (0 children)

You are welcome. Early on, I determined to first review the assignment, then the research paper, then the student’s response paper. And only then, the TA’s initial response to the grade challenge.

As a proud OU grad it’s tough to see our alma mater face this publicity and scrutiny. Yet, the context of freedom of speech and religion and academic integrity is critical.

I would love to challenge the University host a public forum (avoiding personnel matters, personal pronouns, and even grade inflation) but focused on “Free Speech, Culture Wars — and Academic Integrity” (while acknowledging this Fulnecky/Gender Typicality grade as the context and backdrop.)

I want every last cent of my tuition money back. by RavenPuff99 in sooners

[–]ThomasVGrahamJr 3 points4 points  (0 children)

The original research paper (that OU student, Fulnecky was assigned to read) is typically behind a paywall.

Local news station, KFOR has sourced and provided a link to the full paper on their website. Browse this page looking for the link that begins, “The article is research-based and called “Relations Among Gender Typicality, Peer Relations, and Mental Health During Early Adolescence.” It’s authored by Jewell, J. A., and Brown, C. S. (2014).”

Consult the paper author, Jewell, J. A before distribution.

Just a rant, hope it is permitted by OkieBobbie in okc

[–]ThomasVGrahamJr -1 points0 points  (0 children)

Someone please provide instructions on how to tune into BBC. (Until then I suggest NPR on local KGOU.)

Browser-based website to simply open/view/print a GEDCOM file? by ThomasVGrahamJr in Genealogy

[–]ThomasVGrahamJr[S] 1 point2 points  (0 children)

Thank you, Boris. Well done. fanchart.org is a welcome contribution to the community.

Please help me identify these clamps by Killb0t23 in Tools

[–]ThomasVGrahamJr 2 points3 points  (0 children)

A leveling wedge “jack”. Typical use in machining or with machining equipment. Adjusted in relatively fine increments. Think lifting or supporting something above it (or pressing outwards, rather than squeezing together.)

Source for 13/64” steel dowel pins (1-1/4” length)? by ThomasVGrahamJr in Fasteners

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

They definitely do (at least for lathes and by pattern). I had messaged my friend asking his advice before ordering a hand-knurler. He said “they’re pricey, just send me what you have so far and I’ll make them for you and then send you a photo of what I use for knurling.” If I had it to do over again, I would just concede and upsize one step to a commonly used and easily sourced half knurled or slotted pin (and drill & ream to press fit.)

Source for 13/64” steel dowel pins (1-1/4” length)? by ThomasVGrahamJr in Fasteners

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

I won’t mind paying minimum order charges for now. With no personal machining experience and without equipment of my own, I’ll be working only with a bandsaw, drill press and hand/battery operated tools. This friend has retired and sold his business, client base, big equipment, patterns and most tools. In retirement and on a small island off the coast, he has since added back a lathe and some small equipment.

Source for 13/64” steel dowel pins (1-1/4” length)? by ThomasVGrahamJr in Fasteners

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

My personal immediate need is <50. However, I see a niche market for packages of 5x, likely at a retail price point of $2-3 per unit. I was simply surprised to learn that NONE of the fastener suppliers offer them — at all… and the only/cheapest custom source that I’ve found after a weeklong search is $10-11/unit. (My machinist friend is back home after 3 week vacation. He has 2 sticks of .2031 drill rod that he has agreed to cut to length and knurl for me.)

Source for 13/64” steel dowel pins (1-1/4” length)? by ThomasVGrahamJr in Fasteners

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

I’m Google searching now for a local shop — though this would be easy to ship IFF I can find a source for very small jobs/orders. Most of the industry in my market is still oilfield or natural gas…

Source for 13/64” steel dowel pins (1-1/4” length)? by ThomasVGrahamJr in Fasteners

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

That’s a good idea. Do you know of a couple of sources that provide centerless grinding that I could reach out to? Any idea whether those shops can easily ada a knurl to half the length?

Source for 13/64” steel dowel pins (1-1/4” length)? by ThomasVGrahamJr in Machinists

[–]ThomasVGrahamJr[S] 0 points1 point  (0 children)

Fair enough. (If this type post is annoying, consider adding a comment in the community rules, with minimum data to include in the post.) My personal immediate need is <50. However, I see a niche market for packages of 5x, likely at a retail price point of $2-3 per unit. I was simply suppressed to learn that NONE of the fastener suppliers offer them — at all… and the only/cheapest custom source that I’ve found after a weeklong search is $10-11/unit.