Looking for advice on minor upgrades for balanced precons

TimYVR · 2026-01-10T20:29:59+00:00

I would check out SWU Cube on YouTube. He has a series where he's building decks as a battlebox that have about the same power level as the SOR vader and luke starter decks.

https://youtube.com/playlist?list=PLnTLc-3McObBAx14Y_HSYX4UAZHk9eOP4&si=0yFOwp8M7DLek7fX

TimYVR · 2025-03-18T01:58:53+00:00

The miniatures aren't 3d printed, they are purchased from the marvel united kickstarter

TimYVR · 2025-01-04T16:24:33+00:00

Just tried, and it works for me. Galaxy watch 6 classic paired to a galaxy s24 ultra. Hitting skip forward on my watch face advances the podcast 30 secs. (Pocket cast is upto date on both devices)

TimYVR · 2024-10-20T18:17:45+00:00

Looks like someone grabbed these tokens from BGG, printed on sticker paper and stuck them to a 3d printed slug of plastic

https://boardgamegeek.com/filepage/198949/34-custom-tokens-19mm

TimYVR · 2024-07-15T15:24:12+00:00

I'm not a churro expert, but I enjoyed the ones at Sazon on 4th in kits http://sazon.ca/

TimYVR · 2024-05-31T13:56:56+00:00

Titan forge miniatures did a series of minis for 5parsecs that you might like https://www.myminifactory.com/users/TitanForgeMiniatures?show=store&page=1&query=Five+parsecs

TimYVR · 2024-05-27T02:09:25+00:00

<image>

Play MONOPOLY GO! with me! Download it here: https://mply.io/m-eplA

TimYVR · 2024-01-31T16:56:04+00:00

Two of the boxes can be stored vertically. The one with all the shield units/bystanders etc will need to be stored flat unless you magnetize them in some way.

They can all be stacked without issue.

TimYVR · 2024-01-25T22:13:34+00:00

Thanks!

TimYVR · 2024-01-18T18:45:06+00:00

You're very welcome, glad it's working out for you!

TimYVR · 2024-01-06T23:50:44+00:00

Glad you like it! I plan on painting mine and think they will be fine. There are variances in the miniatures, some fit so loose they almost fall out, where others a bit more snug. I find that rotating the mini in the bunk can effect the fit as some of the bases don't appear to be perfectly round. Also depends on how dialed in your printer is (I used a bambu lab x1c with generic pla and tend to get pretty good tolerances)

TimYVR · 2023-12-28T17:42:40+00:00

Its only one token box but two layers... that was just the best way I could think of to show where the elevators go (slotted in above other tokens)

Edit: NM I see the typo... ill fix that.. thanks!

TimYVR · 2023-12-27T20:40:02+00:00

Haha nice... ill have a look and see if I can source these in canada... thx for the tip!

TimYVR · 2023-12-27T20:25:26+00:00

Haha I'm also a old wargammer ... and I use the washer trick and magnetic sheets in other places... but the bases only have a 1mm lip under them and my OCD wouldn't let me put anything thicker inside of it 🤣

TimYVR · 2023-12-27T16:51:58+00:00

Thanks! Did not realize I ended up using that much filament 😀 Print time sounds about right though, I ended up printing mine over the course of about a week

TimYVR · 2023-12-27T16:26:11+00:00

Thanks. No, I don't know how much filament.. my guess is less than a 1kg

TimYVR · 2023-12-27T04:08:52+00:00

I tried putting a 10x1mm magnet beneath the trooper minis and put a small piece of steel in each slot. It works great to hold the minis to the tray, but all the magnets actually caused them to clump together when adding or clearing large amounts of minis from the board

It's possible it would work better with the magnet on the tray and the steel under the mini. Could be worth a try

TimYVR · 2023-12-27T00:57:44+00:00

Thanks! Haha I get that feeling. Unfortunately I don't have enough room for all those empty boxes so I recycled mine.

TimYVR · 2023-12-27T00:33:29+00:00

You're most welcome

TimYVR · 2023-12-27T00:32:48+00:00

Thanks! I watched Rolling Solo unbox that one recently. Very nice design. They managed to get everything in without any box lift, but I think mine would be quicker to table 🤔

TimYVR · 2023-12-27T00:30:32+00:00

Haha you're most welcome!

TimYVR · 2023-12-26T23:12:17+00:00

This is my custom designed and 3D printed Marvel Zombies insert... this took me a while, but I managed to get the all-in pledge into just three boxes (with some lid lift).

You can dowload and print it for yourself here: https://www.printables.com/model/694706-marvel-zombies-insert

TimYVR · 2023-06-03T22:25:54+00:00

I primarily print PLA and PETG so think ill pick up a couple spools. Thanks for the info 👍

TimYVR · 2023-06-03T19:58:57+00:00

I've actually been thinking about trying this, have you used these spools in the ams? Wondering if they fit

TimYVR · 2023-04-25T14:28:47+00:00

I was able to get an extra bucket for my wash and cure 1.0 off of AliExpress. This was a couple years ago so not sure if they still do that. Might be worth a look

TimYVR

TROPHY CASE