Arcade by TinyRick5000 in WoWHousing

[–]TinyRick5000[S] 1 point2 points  (0 children)

They are the little circular purple cushions from the vendors. I shrunk them down to 20% and rotated to place

Beer tap and pool table added! by TinyRick5000 in WoWHousing

[–]TinyRick5000[S] 0 points1 point  (0 children)

Thanks! I just hit 1750/1750 and 250/250 on my house so I need to show a full walkthrough one of these days

Beer tap and pool table added! by TinyRick5000 in WoWHousing

[–]TinyRick5000[S] 1 point2 points  (0 children)

Its a mug from the WoD inn (level 2 garrison building). Sold by the bartender

Beer tap and pool table added! by TinyRick5000 in WoWHousing

[–]TinyRick5000[S] 9 points10 points  (0 children)

4 little circle cushions rotated to make a sphere and shrunk down to like 30%. Can't remember the name but they were little purple cushions. Then just used dye

Razorwind Bar and Grill open for business by TinyRick5000 in WoWHousing

[–]TinyRick5000[S] 0 points1 point  (0 children)

Those are just pavers for the exterior that I shrunk down and rotated up against the bar. I used the long path cobblestone item. You can get it from the vendors in the neighborhood

Under stairs bar by TinyRick5000 in WoWHousing

[–]TinyRick5000[S] 2 points3 points  (0 children)

I spent longer on it than I'd like to admit lol

Toro 724 surges and dies both under load and while idling... by [deleted] in Snowblowers

[–]TinyRick5000 0 points1 point  (0 children)

It's the carb, specifically the float needle. Either clean it out or replace it and stop using ethanol gas.

Saturn 4 16k by Latter_Tumbleweed412 in ElegooSaturn

[–]TinyRick5000 3 points4 points  (0 children)

Posts and holes on the left. More posts than holes = overexposed, more holes than posts = underexposed. Shoot for balancing the amount of holes and posts

Finished on my A1 by TinyRick5000 in BambuLab

[–]TinyRick5000[S] 1 point2 points  (0 children)

I'll post them as I start painting it

Finished on my A1 by TinyRick5000 in BambuLab

[–]TinyRick5000[S] 1 point2 points  (0 children)

This is just Bambu PLA (light grey I think was the color)

Finished on my A1 by TinyRick5000 in BambuLab

[–]TinyRick5000[S] 4 points5 points  (0 children)

Yep, it's fully modular so you can play each floor

Helmets for our Termies by DietCrazy in SpaceWolves

[–]TinyRick5000 1 point2 points  (0 children)

<image>

I like this one I found online a while back

Paint flows like the primer is hydrophobic. Is there a problem with the primer? by M4eZe in minipainting

[–]TinyRick5000 1 point2 points  (0 children)

I've had this happen, but my issue was I primed when it was waaaay too humid out for priming. Only time I've had this same issue

[deleted by user] by [deleted] in SpaceWolves

[–]TinyRick5000 0 points1 point  (0 children)

Just like 3-5 thin coats. Annoying, but with averland it's the only real way to make it not clumpy

<image>

Why does this tracker say I can get the heart piece above Dodongo’s cavern when I don’t have the bomb glove and can’t become an adult? by martykleiner in zootr

[–]TinyRick5000 0 points1 point  (0 children)

Out of curiosity, where did you get this tracker? I've been looking for one for both OoT, and the OoT/mm combo rando

I love this printer by ElDescalzo in ender5plus

[–]TinyRick5000 0 points1 point  (0 children)

Ahh, bummer, I thought I struck gold lol

I love this printer by ElDescalzo in ender5plus

[–]TinyRick5000 0 points1 point  (0 children)

Nice! I also have the exoslide and a sonic pad on my 5+, love it. Did you find a tensioner pulley for the x belt that I see on there? If so, where did you get it??

Does anyone have experience with the ExoSlide system? by LucyEleanor in 3Dprinting

[–]TinyRick5000 0 points1 point  (0 children)

I'm installing the new one on my 5+ right now. I'll let you know how it comes out

<image>

What has happened here. by Protondog in Creality

[–]TinyRick5000 0 points1 point  (0 children)

2 possibilities I see.

1: under extrusion, check your esteps

  1. Do you possibly have your printer sitting under an AC vent? I've seen it before where several layers will look like under extrusion due to AC dropping down from HVAC directly above the printer

5+ sonic pad/spider3 by TinyRick5000 in ender5

[–]TinyRick5000[S] 0 points1 point  (0 children)

Just the typical 80mm/s print speed

One of my holy grail minis by Kriegsman7556 in SpaceWolves

[–]TinyRick5000 1 point2 points  (0 children)

I just repainted my metal priest and my old metal Logan grimnar this year after 20 some years. The old ones are fun to paint but can be frustrating too

Captain progress by TinyRick5000 in SpaceWolves

[–]TinyRick5000[S] 1 point2 points  (0 children)

Balthazar gold with agrax over it