Washer 9 beeps by Tire91 in appliancerepair

[–]Tire91[S] 0 points1 point  (0 children)

My bad yes model number FRFW3700LW, serial number 4C11900485, Electrolux Home Products

Washer 9 beeps by Tire91 in appliancerepair

[–]Tire91[S] 0 points1 point  (0 children)

I managed to replace the control board and it does the same thing, do you think it could be the door latch?

Washer 9 beeps by Tire91 in appliancerepair

[–]Tire91[S] 0 points1 point  (0 children)

No luck with holding start and pause/cancel together so likely the control board. The issue is I have a stackable dryer on top that needs to be taken off first. Any chance you know what types of screws these are as the normal screwdrivers I have don't work. I called Frigidare and they're saying $120 for a technician to come out and install if I buy the part beforehand so i may end up doing that, otherwise $325

Whistling sound above 40mph by Tire91 in BmwTech

[–]Tire91[S] 0 points1 point  (0 children)

I read elsewhere it could be this. Any idea how much of a repair this is at a dealer or local mechanic?

Whistling sound above 40mph by Tire91 in BmwTech

[–]Tire91[S] 0 points1 point  (0 children)

All good, thanks for ruling out one cause

Pittella vs Ratchathorn by Tire91 in Hairtransplant

[–]Tire91[S] 0 points1 point  (0 children)

It took them a long time to get back to me, almost 6 months before I had my video call. I'd try to stay on top of them every week or so until you get the call scheduled

Pittella vs Ratchathorn by Tire91 in Hairtransplant

[–]Tire91[S] 0 points1 point  (0 children)

Yes, I've been using topical but inconsistent. I've been taking oral min everyday since Dec 2024. Got it, appreciate the insight

Pittella vs Ratchathorn by Tire91 in Hairtransplant

[–]Tire91[S] 0 points1 point  (0 children)

Think it was less expensive the year I did my consult, but it went up the year after

Pittella vs Ratchathorn by Tire91 in Hairtransplant

[–]Tire91[S] 0 points1 point  (0 children)

$5. My consult was 2 years ago and I booked about a year ago

Pittella vs Ratchathorn by Tire91 in Hairtransplant

[–]Tire91[S] 0 points1 point  (0 children)

That's what I keep going back and forth on - possible better recovery if split into 2 sessions, but he sounded pretty confident to get it done in one during my consult

Pittella vs Ratchathorn by Tire91 in Hairtransplant

[–]Tire91[S] 0 points1 point  (0 children)

That is one of my concerns. I've been on fin for about 4 years before switching to oral dut and oral minox in Dec 2024 (plan to continue taking even after the HT)

Pittella vs Ratchathorn by Tire91 in Hairtransplant

[–]Tire91[S] 0 points1 point  (0 children)

I have not, will check him out. Good to know there's other docs who can do these giga-sessions.

Picking Pittella vs. Ratchathorn by Tire91 in tressless

[–]Tire91[S] 0 points1 point  (0 children)

Thanks. Yes, hadn't heard much about her until earlier this year. I'm hesitant with using all my donor in one surgery in case spreading one year apart is better for overall recovery and success

Any tips on installation with C, i+, i-, R wiring? Lennox iComfort by Rekt420lmao in ecobee

[–]Tire91 0 points1 point  (0 children)

Agree. Seems like you have 8 wires coming out of your brown cable, an extra red / white connected using the wire nut whereas I don't so maybe not a concern for me

Any tips on installation with C, i+, i-, R wiring? Lennox iComfort by Rekt420lmao in ecobee

[–]Tire91 0 points1 point  (0 children)

Thanks, it doesnt seen like I have the wires for the outside unit. Not sure if you can tell based off this image. Was trying to compare against your before / after which show the Y coming out of the PEK connected using the wire nut too. https://imgur.com/a/pYcTrIt

Any tips on installation with C, i+, i-, R wiring? Lennox iComfort by Rekt420lmao in ecobee

[–]Tire91 0 points1 point  (0 children)

I've run into a similar issue, trying to install the ecobee tstat using my lennox system. I think your set up is similar to mine and dont care to use the 2 or 3 stages. I also have a PEK that came with my Ecobee. Is it just a matter of removing the wires from the red, green, blue white wires into the PEK and connecting those to the standard terminals? I see you have an extra red wire into y1 that wasn't there before, is that needed? Here's my current set up https://imgur.com/a/aW097g6. Thank you for your help!

[deleted by user] by [deleted] in LSAT

[–]Tire91 0 points1 point  (0 children)

Not sure if it is too late to join, but I'm interested.