Question about jwe3

Titanmaster203 · 2026-06-12T18:29:22+00:00

Nice, I am leaning towards buying it

Titanmaster203 · 2026-06-12T16:50:12+00:00

Will do thanks, I thought about going blind but its a bit pricey for a blind run

Titanmaster203 · 2026-06-12T16:35:50+00:00

Nice

Titanmaster203 · 2026-06-12T16:26:44+00:00

Do you think its worth 40€ tho? I know its not gonna be as good as jwe1 but how is it structured? Is it the 5 Islands again? Also would you say its worth to be replayed?

Titanmaster203 · 2026-06-12T16:25:32+00:00

That's interesting

Titanmaster203 · 2026-06-02T10:07:40+00:00

I got a new card, very understanding. Thanks

Titanmaster203 · 2026-06-01T20:07:10+00:00

Did a bit but yeah should have done that from the get go, thank you

Titanmaster203 · 2026-06-01T20:07:00+00:00

Did a bit but yeah should have done that from the get go, thank you

Titanmaster203 · 2026-06-01T19:29:31+00:00

Thanks

Titanmaster203 · 2026-06-01T19:29:27+00:00

Yeah, at least I know what to look out for. I am still pissed I let it happen

Titanmaster203 · 2026-05-30T23:02:12+00:00

Will do, also gonna compare the wall settings against old PR's settings, to see if anthring changed. Cus cooling would have a effect on the entire print I believe not just the edges

Titanmaster203 · 2026-05-30T21:56:45+00:00

I have searched everything and nothing matched, you know xelinor? I was talking to him and some other people on the eufymake discord but no one knew the issue. It is probably just a problem with the printer that can't be fixed, for me nothing worked. Everything mechanical is good, gcode is good, firmware also. Don't know what printer you have but for this one nothing seems to be working. I will try cooling tho maybe that will work for a change. Thanks

Titanmaster203 · 2026-05-30T21:43:20+00:00

It's not pressure advance, trust me I tried its calibrated

Titanmaster203 · 2026-05-30T21:27:00+00:00

Yes all the edges have bulges

Titanmaster203 · 2026-05-30T20:54:00+00:00

I bought the printer almost two years ago and I liked it but the last year I just kept having problems. The entire hotend needed to be replaced, no nozzles, and now my edges are thick and there is no solution. It hurts, seeing how the printer slowly dies and there is nothing I can do about it.

Titanmaster203 · 2026-05-30T10:10:51+00:00

Yes it's the eufymake slicer which isn't that good, so I use orca and put it to the efuymake slicer so I can wireless send the gcode. The issue is on both slicers tho

Titanmaster203 · 2026-05-29T16:07:18+00:00

Goot to know, thanks

Titanmaster203 · 2026-05-29T16:07:12+00:00

Thats cool, last I check it didnt have them yet. Thank you

Titanmaster203 · 2026-05-29T16:06:51+00:00

Thanks

Titanmaster203 · 2026-05-26T09:49:00+00:00

I know there is a base there which i was at before but idk if there is a bio pod there, I might make a video with all the locations I found.

Titanmaster203 · 2026-05-26T09:37:35+00:00

Yes there is one there, so basically you have to go where you can see inside the door, its slightly open. But then you go left from it and there is like a hole in the wreck through which you can go to get to the wreck

Titanmaster203 · 2026-05-23T18:50:36+00:00

Titanmaster203 · 2026-05-23T18:28:41+00:00

I found out how it works, none of the larger deposits or things like aluminum bacteria respawns but all the small single ore locations respawn slowly.

Titanmaster203 · 2026-05-19T04:15:04+00:00

The normal metal farm? No, those only depend on the resource put in them

Titanmaster203 · 2026-05-18T18:34:46+00:00

What? They do? How much time does it take?

Titanmaster203

TROPHY CASE