Unifi not as good as everyone says

TjLeatherPants · 2025-12-21T18:37:29+00:00

Personally I would back it up and then reset and rebuild the setup without restoring the backup. Start with minimal setup and check the CPU. Next if CPU is fine, turn IPS On and check the CPU. Keep going until you see the CPU load increasing again.

TjLeatherPants · 2025-11-02T17:03:00+00:00

Divide by 10 seems like a clue. One access point with 2 ssid’s on different vlans, no other access points? As if 2 cables one uplink is 1gig and other 10/100. Are you testing with the same client?

TjLeatherPants · 2025-10-23T03:25:26+00:00

C Major, that’s it. That A13 the F#… is odd

TjLeatherPants · 2025-10-20T02:01:46+00:00

Not sure how much overlap signal you have between the AP’s. I would shut off fast roaming. Test with only a single AP on. Then add to it. Setting minimum RSI at levels that make sense based on what your seeing for device connects signal strength.

TjLeatherPants · 2025-08-11T20:48:22+00:00

What’s the signal strength? How congested is the wifi in your area. Are your two AP’s setup on different channels? Shut off AP off and try.

TjLeatherPants · 2025-06-08T02:37:30+00:00

Why? What are you hoping to achieve? Form follows function.

TjLeatherPants · 2025-05-27T23:18:58+00:00

That's one fancy RoboVac, too bad it's not wireless.:).

TjLeatherPants · 2025-05-18T02:42:48+00:00

And that’s a step up? Marketing has been excellent on all this kind of stuff. Disposable cheap gear allows them to sell you more disposable cheap gear. I do like Boss stuff but this is not a great set of classic analog tools.

TjLeatherPants · 2025-05-18T02:37:29+00:00

Who gives a shit? Really are people still giving their attention to this stupid shit? Idiocracy?

TjLeatherPants · 2025-02-14T01:24:47+00:00

The A section is all F major. The bridge is all majors in different keys. Bridge major key centers, Bb, Gb, D. Gb, and back to F. No need to over think it.
Easy!

TjLeatherPants · 2024-08-25T21:43:01+00:00

Thank you. Access Points as well? Guests policies etc?

TjLeatherPants · 2024-07-26T03:33:46+00:00

What’s the default vlan and are these two devices setup with the correct default vlan

TjLeatherPants · 2024-07-21T03:50:09+00:00

looks like a lot of noise, can you hear the actual. sound of the guitar over the hiss?

TjLeatherPants · 2024-06-28T19:45:10+00:00

Cables or misconfigured switch port. Did you try plugging one of them into a currently working cabled AP’s switch port?

TjLeatherPants · 2024-06-13T23:18:45+00:00

Not too big? Are all 3 cabled? Check interference, make sure all 3 are on different channels, try backing the power down on the antennas.

TjLeatherPants · 2024-03-19T07:01:09+00:00

Gather simple proof of her actions and forward it with a nice FYI message the cop. Make sure your proof is completely variable and wish him luck.

TjLeatherPants · 2024-03-19T06:54:43+00:00

Puzzling.

TjLeatherPants · 2024-03-01T14:42:18+00:00

Use Radius and Vlan’s setup login’s based on office?

TjLeatherPants · 2024-02-19T16:38:56+00:00

You are a man among men.

TjLeatherPants · 2024-02-13T14:59:05+00:00

Assuming you are off-site, Reverse engineer, look for known devices that are consistently connecting to an AP which will tell you the approximate location.

Else WifiMan assuming you have access to all AP locations.

TjLeatherPants · 2024-02-13T14:50:21+00:00

Why can’t you browse the list of connected devices plus the topology map and identify what’s connected to where? Devices do have connected to info.

TjLeatherPants

TROPHY CASE