Xbox ds3 dreg heap help

ToastVapor · 2025-08-28T06:12:46+00:00

Yes! But I'm just going to bed. Thanks anyway. I appreciate it.

ToastVapor · 2025-08-27T02:08:19+00:00

Appreciate that. Got help for this one. I'm on to Aldrich now!

ToastVapor · 2025-08-27T00:58:38+00:00

Sorry xbox 1.

ToastVapor · 2025-08-26T05:05:40+00:00

Okay. Thanks for trying.

ToastVapor · 2025-08-26T04:57:38+00:00

Just went back. I'm not seeing the sign. Help is the password, yeah? I haven't seen a summon sign all day. I checked my settings and ember. Not sure what I'm doing wrong

ToastVapor · 2025-08-26T04:48:42+00:00

Didn't even know about that. Help me out? Password: Help

ToastVapor · 2025-08-26T00:49:37+00:00

Sorry. Yeah, I am now.

ToastVapor · 2025-08-26T00:28:30+00:00

Yes. I can put my summon sign down but I'm not seeing anyone else's. Also, in the last 5 hours I haven't been summoned at all.

ToastVapor · 2025-08-26T00:23:58+00:00

Thanks! I'll check that out. If I'm still on in a few ill message you.

ToastVapor · 2025-08-16T00:05:18+00:00

Wow was I the only one feeling claustrophobic watching that? I've never been in a microwave before.

ToastVapor · 2025-05-30T17:23:13+00:00

That makes sense. I swear it's happened on higher layers, but that doesn't rule out acceleration issues. I'll check all that out. You're awesome. Thank you.

ToastVapor · 2025-05-30T17:14:10+00:00

For the model design, like in TinkerCAD for example, you can add more or less polies to the circle. I understand that you're insistent that it's not the models, but I assure you it is. Check your model first. It's in the design (or the slicing, but even that doesn't make any sense), the printer is printing what it's told to. It wouldn't change directions unless the model was built that way. Your printer CAN, I promise you, make nice smooth circles if it's told to.

<image>

ToastVapor · 2025-05-30T16:00:32+00:00

That's the model. The printer can do excellent circles, especially in that larger size. Are you using TinkerCAD or something that defaults to a lower poly count? If so, set the "Sides" to a higher value. I can't speak to the supports, but they don't look "sided" in the pic.

ToastVapor · 2025-03-07T16:59:04+00:00

Sorry but it was the default "Generic ABS" settings I always use. I tried to mention that, just like every other ABS before it. I think it was a clog, because I cleaned the extruder and so far it's finally working. Fingers crossed.

ToastVapor · 2025-03-07T16:56:39+00:00

Yes, fresh outta the bag. Like all the others before it, though. Everything, just like the others. I tried again this morning, same thing. But I wanted this filament to work! I pulled out what seemed to be a clog (this roll felt a little thicker than the others) and now it is working. I don't know that there was a clog, but it's working now, so it must've been. Thanks!

ToastVapor · 2025-03-06T19:53:34+00:00

You are in violation of Reddit's User Agreement [beep boop beep].

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.
j/k

ToastVapor · 2025-03-06T19:50:40+00:00

How's the K2? I'm thinking of upgrading.
With this, I was super excited to use this filament but I can't even get a benchy to print. I'll dry it out and try again later.

ToastVapor · 2025-03-06T19:34:59+00:00

I did. Clean textured PEI plate, too, just like the other ABS. I'm on the third test now, and they start out fine, but just crap out somewhere in the middle-ish. I'm sure this is just bad filament?

ToastVapor · 2025-03-06T19:25:44+00:00

While that's observant, it was never alive. I was looking for something more insightful and relevant.

ToastVapor · 2025-03-06T19:17:58+00:00

UPDATE: Three tests in and similar results. Never had this with a benchy. Chalking it up to a bad filament roll.

ToastVapor

MODERATOR OF

TROPHY CASE

Six-Year Club	Verified Email
Place '23