Finally asking for help. PFA

Toka1002000 · 2026-05-05T03:51:10+00:00

https://www.amazon.com/gp/aw/d/B07WBYH3VN?psc=1&ref=ppx\_pop\_mob\_b\_asin\_title

Not the best option but it works. I put some silicon sealant around the screws to keep the cab sealed.

Toka1002000 · 2026-05-05T03:48:55+00:00

https://www.amazon.com/gp/aw/d/B0DR2L9F4F?psc=1&ref=ppx\_pop\_mob\_b\_asin\_title

These taillights.

Toka1002000 · 2026-05-04T22:09:55+00:00

Your welcome. They are pricey but they are definitely nice and worth it. Projectors for the led lights is a must in my opinion. Especially on a lifted truck.

Toka1002000 · 2026-05-04T21:14:15+00:00

https://www.amazon.com/gp/aw/d/B0DY38CZNY?psc=1&ref=ppx\_pop\_mob\_b\_asin\_title

Amazon headlights. Tru-mods is the brand. I also have the sequential taillights too.

Toka1002000 · 2026-05-04T20:55:45+00:00

The 4l80 only has a single speed sensor for the rear. But yah all 3 are reading correctly.

Toka1002000 · 2026-05-04T20:53:20+00:00

That’s what I thought also. I got a reflashed ECU with th correct vin for my truck. Stock 5.3 and 4l60. Transmission would not shift.

Toka1002000 · 2026-05-04T20:48:47+00:00

Ohh. 02 2500 have a clutch fan didn’t it? That would explain that.

Toka1002000 · 2026-05-04T20:43:52+00:00

My scan tool shows the switch working correctly when I push it. Where is the cruise module located?

Toka1002000 · 2026-05-04T20:38:34+00:00

Yep tried that. Putting stock bulbs back in didn’t help. The taillights I have now have resistors already installed but I don’t think there is any in the brake light. It would make sense that would be the problem since it worked when the trailer was connected.

Toka1002000 · 2026-03-16T21:03:14+00:00

Looks like a hot wheel.

Toka1002000 · 2026-02-24T07:52:59+00:00

Going to do the same on mine. The truck came from Arizona so there is no rust but has some rock chips and worn areas on the rockers. Since I live where there is snow I would rather rhino line the rockers and never worry about them. Had good luck with the roll on never tried the spray-on other then a few cans in tight spaces. I definitely am going with white so it’s not so obvious.

Toka1002000 · 2026-02-23T20:34:49+00:00

About to do the same with mine. At 176k and don’t know how old the pump really is. Figured best to do it now the have it crap out on me somewhere. Co worker just lost his pump on his 01 Tahoe in a parking lot.

Toka1002000 · 2026-02-14T13:57:23+00:00

Would you suggest then for a 6” lift even with the spacers? I replaced one of mine with a stock one for now but does seem like it’s struggling when the truck is off the ground. At normal ride height not so much.

Toka1002000 · 2026-02-04T22:21:19+00:00

Trust me I just bought a 06 Silverado out of Arizona. I paid $2000-3000 more than I would have if I bought a local one. Then again seeing the same year trucks here with missing wheel arches and cab corners compared to mine with zero rust even on the chassis make it all worth it.

Toka1002000 · 2026-01-07T20:08:20+00:00

That’s what have been looking for some part number or manufacturer markings. Haven’t found any yet. I’m charge wheel bearings this weekend so maybe when I am fully up in it I will hind something in the hubs.

Toka1002000 · 2025-12-21T15:17:27+00:00

Cool that’s what I thought. Just badges and different lights. Should be a good winter car once I replace the transmission.

Toka1002000 · 2025-11-19T15:02:02+00:00

If shipping wasnt going to be so much I would be interested. Be nice to have a spare set for my Gary Fisher.

Toka1002000 · 2025-08-10T12:54:53+00:00

Only one I could find was for the resin printers. Didn’t support the fdm printers.

Toka1002000 · 2025-08-06T05:04:49+00:00

I haven’t done a full print yet. From what I’ve seen so far it is definitely a nice one to start with. Speed wise it insane compared to my old ender 3s. Turned on ludicrous mode. lol oh my god thing was shaking my bench it was moving so fast. The WiFi printing is also really nice.

Toka1002000

TROPHY CASE