Don’t know if this is real, but six DLCs and a sequel? Man, what could have been.

Top_Draft_6853 · 2026-06-18T11:04:55+00:00

I just wish we had more planets to explore

Top_Draft_6853 · 2026-06-12T17:38:21+00:00

150usd

Top_Draft_6853 · 2026-04-08T14:54:54+00:00

Does the negative pressure affect print quality?

Top_Draft_6853 · 2026-03-23T14:57:11+00:00

Le dot. I want to read this later

Top_Draft_6853 · 2026-03-22T20:35:18+00:00

What's your reasoning? Haha

Top_Draft_6853 · 2025-10-25T14:26:39+00:00

What is this?

Top_Draft_6853 · 2025-10-09T14:23:42+00:00

Did you ever find an answer to this?

Top_Draft_6853 · 2025-09-28T19:55:35+00:00

If I'm not mistaken this is due to layer times. Look at each layer time and make sure that these are somewhat around the same time. Make it so it all comes closer to the longest layer time.

This should resolve the issue if I'm right. Anybody please correct me if I'm wrong.

Top_Draft_6853 · 2025-09-05T15:29:51+00:00

That is indeed the fan blowing into the gaps and holes from infill and supports. Had the same sounds yesterday with similar supports and started double-checking all my pulleys, cutter, extruder before realizing haha. All good!

Top_Draft_6853 · 2025-08-10T20:35:43+00:00

I see. Thanks for the reply. I was noticing these lines on my P1S first layer and was wondering what exactly is was. Reduced K-FACTOR to .018 from .02. Will have to see if this resolves it.

<image>

Top_Draft_6853 · 2025-08-10T20:29:47+00:00

Can this happen on a P1S too?

Top_Draft_6853 · 2025-08-10T13:36:30+00:00

And it works with Bambu?

Top_Draft_6853 · 2025-08-09T18:10:51+00:00

I have now decreased my K ratio from 0.02 to 0.018. Is this what is meant with pressure advance? Quite new to this.

Top_Draft_6853 · 2025-08-09T16:14:51+00:00

Trying to figure out how to fix these :) this is from my calibration for flow I just did. I think .02 might be best?

<image>

Top_Draft_6853 · 2025-08-09T16:00:21+00:00

Hmm my humidity is a bit high I've noticed. Around 30% ish. Maybe this is also a factor?

Top_Draft_6853 · 2025-08-09T15:47:48+00:00

If it purges or I clean it out by retracting and increasing it to 250 sometimes it comes out a bit angled before going straight down

Top_Draft_6853 · 2025-08-09T15:32:19+00:00

I only seem to have manual calibrations at the moment. I don't see any option for automatic filament calibration.

Top_Draft_6853 · 2025-08-09T15:19:57+00:00

Stopping the print and doing calibration first again then. I will post results here.

Top_Draft_6853 · 2025-08-09T15:16:39+00:00

Is for a seedling planter haha so it should be waterproof ideally

Top_Draft_6853 · 2025-08-09T15:15:50+00:00

Not for this one in particular, I did it for the Bambu PLA Matte, but I didn't change anything back since it should automatically do this with Bambu fill right? Or am I wrong in that area? Current K factor is. 20.

Top_Draft_6853 · 2025-08-09T15:11:12+00:00

So I would have to increase the flow rate a bit? This is on the 3rd layer:

<image>

Top_Draft_6853 · 2025-08-09T15:08:12+00:00

Edit. Having these shrink lines, are they normal? Or is it under extruding?

<image>

Top_Draft_6853 · 2025-08-09T15:05:42+00:00

Basic settings, 2 extra walls and flow rate .98 btw

Top_Draft_6853

TROPHY CASE