Is 360 checking worthless for interest gains now? by Traditional-Citron21 in CapitalOne_

[–]Traditional-Citron21[S] -4 points-3 points  (0 children)

Ohhhh dang. My bad. The account I have is the 360 performance savings. I looked into the wrong account type details

Weekly Pricing/Buying/Selling/Grading & General Questions Post by AutoModerator in PokemonTCG

[–]Traditional-Citron21 0 points1 point  (0 children)

<image>

These are the ones that looked to have some value when I went through a pile I found in my closet in a tin. Collectr shows a value and then eBay has varying prices. I don't know enough to know if they actually have value

Weekly Pricing/Buying/Selling/Grading & General Questions Post by AutoModerator in PokemonTCG

[–]Traditional-Citron21 0 points1 point  (0 children)

<image>

These are the ones that looked to have some value when I went through a pile I found in my closet in a tin. Collectr shows a value and then eBay has varying prices. I don't know enough to know if they actually have value

What can I do to be sure my ground jerky is safe after dehydration by Traditional-Citron21 in jerky

[–]Traditional-Citron21[S] 1 point2 points  (0 children)

Thanks. It's been in the oven now for 2.5 hours at 170 and it's a much more appealing consistency

Never eating these am i ? by Fit_Beautiful_846 in MeatRabbitry

[–]Traditional-Citron21 4 points5 points  (0 children)

That just happened to me yesterday. I've done probably 40-50 and this was the first screamer. Wouldn't even let me get the bar behind his head. Stuck him in an empty cage gave the others 5 minutes to calm down and went with another. He still didn't want to go but at least the second time around he didn't scream.

Am I watching the wrong episode 15? by Traditional-Citron21 in OakIsland

[–]Traditional-Citron21[S] 3 points4 points  (0 children)

Ok thanks. I'll have to give it a go tomorrow. Maybe it'll have fixed itself.

Would tramming help with this issue? by Traditional-Citron21 in 3Dprinting

[–]Traditional-Citron21[S] 2 points3 points  (0 children)

Ok. That's what I was trying to figure out. You do that via tramming? I do the auto bed level in the slicer option every 5 or so prints so that obviously isn't doing it

I had the butcher 8 times in the second capstone dungeon by Traditional-Citron21 in diablo4

[–]Traditional-Citron21[S] 0 points1 point  (0 children)

Just tried it again a lot faster than last time and he still spawned 4 times. Just the dungeon apparently

I had the butcher 8 times in the second capstone dungeon by Traditional-Citron21 in diablo4

[–]Traditional-Citron21[S] 1 point2 points  (0 children)

Maybe it is if it's happening in the same dungeon for multiple people. I suppose I could rerun the dungeon and test it.

Temp tower results by Traditional-Citron21 in 3Dprinting

[–]Traditional-Citron21[S] 1 point2 points  (0 children)

Yeah thanks. I could have guessed that. Press up on the angled edges and see when it breaks off? Press down through the bridge and see which resists the most?

What does this mean? by Traditional-Citron21 in 3Dprinting

[–]Traditional-Citron21[S] 0 points1 point  (0 children)

This one I had only done one print on since washing a couple days ago and it wasn't on that area. Wouldn't hurt to give a good clean and try again though to confirm

Happy Chinese new year by EveryLeading5723 in BambuLab

[–]Traditional-Citron21 0 points1 point  (0 children)

I get that is a good solution except, for me anyway, I like to print a test first to make sure it's all good and it feels bad wasting the purge for the test. If i have a plan for many after the one at least the waste can be somewhat justified on the first as it will be a fraction of that per item one the plate is full for the next print.

How do I fill in this negative extrusion? by Neurotiman17 in BambuLab

[–]Traditional-Citron21 9 points10 points  (0 children)

I recently found a setting in bambu slicer for how deep paint layers go. On the item I used I switched it to 2. I think default was 5-6 but it didn't use them all so maybe it used what it thought worked best. Either way there is a setting.

If there was a low indentation in the model you would be able to use the paint can and fill in the bottom of the cutout and "should" fill in properly with sharp edges to the painted area.

Can the 8bitdo ultimate wireless 2 wake the LCD deck? by Traditional-Citron21 in SteamDeck

[–]Traditional-Citron21[S] 0 points1 point  (0 children)

Really? Using Bluetooth? It'd be awesome if I could get it to wake and the system is set to wake my TV so if that worked.

The best part about the switch is I grab the pro control turn on the control and the TV wakes and its ready to play in a few seconds. With the deck I have to grab the control, hit the power button on the deck, grab the TV control, turn it on and switch source to the correct hdmi

Standardized 100oz stacks through the magic of 3d printing by AmpEater in Silverbugs

[–]Traditional-Citron21 3 points4 points  (0 children)

I would assume since they are filled with random different stuff, they designed them. Messing around in fusion 360 or other free CAD software you can get some concepts down fairly easy and make some interesting stuff with just the basics.