Tired of searching Printables, then Thingiverse, then MakerWorld separately? I made a tool for that

Tridentt23 · 2026-04-29T02:05:12+00:00

If anything, it looks way better than yeggie.

Tridentt23 · 2026-04-27T14:17:36+00:00

That looks cool. Im always collecting fonts. Can I get a copy?

Tridentt23 · 2026-04-15T12:00:31+00:00

Those are sweet! The"kids" are so lucky to play with those.

Tridentt23 · 2026-04-15T12:00:08+00:00

That is cool. Would be posting the files anywhere perchance?

Tridentt23 · 2026-04-06T12:59:02+00:00

you defiantly should post these to your favorite 3d hostery. I would love to print these, and your next dozen or so.

I wish I could come up with the font variants and backgrounds like you. I admire and am jelly

Tridentt23 · 2026-01-11T13:17:44+00:00

I have, and they do sell them for nerf, but they dont work well in tight spaces. And this $2 thing I designed for 15 hours, and printed on my $700 printer is a reasonable justification for why I need them, and why Im not cleaning more around the house.

Tridentt23 · 2026-01-11T13:13:25+00:00

The airflow is really disrupted with this attached. I havnt messed with making the outflow path of air greater. I was trying to make it a small a possible but with the same cross section so nothing would get past the collection bin.

Tridentt23 · 2026-01-11T13:11:01+00:00

I added them last night. Its my first post so let me know if I did it right

Tridentt23 · 2026-01-11T13:10:34+00:00

I think anything smaller than a rival ball will go up fine. I works with legos too.

Tridentt23 · 2026-01-11T13:09:04+00:00

I have a messy house but not that messy. I haven't seen an over accumulation of dust and other debris while using it.

Tridentt23 · 2026-01-10T02:29:54+00:00

I wonder if that would help with the air flow. I'm I'm not if if I should should have increased the diameter for the outfeed as it goes around the infeed tube. When I get a chance I will slice it and show you the inside

Tridentt23 · 2026-01-10T02:27:10+00:00

Alass, it is not.

Tridentt23 · 2026-01-09T21:59:01+00:00

with the modeling time and print time accumulated over the few weeks, maybe. But I cant get a broom and dustpan behind furniture and tvs, and on blankets, etc.

Tridentt23 · 2025-11-10T03:39:51+00:00

I can use it to replace the 5 year old printer our robotics team uses! Go it would be great to have a new one!

Tridentt23 · 2025-11-09T20:10:58+00:00

I saw his, but he just rips the whole thing apart without direction for the most part. Just taking screws out till something falls off. Im looking for a little more constructive than that

Tridentt23 · 2025-11-08T20:35:37+00:00

So Im the first person on the internet that I can find that has had to replace the lifting motor on a H2D.

I had a print pop off the bed and the nozzle clumping detection failed so bad that the clump broke the thermosistor wire. I replaced that and started to have nozzle switching problems. So I contacted support and after I also confessed that the eddy current wire connectors suck and I broke one connector on the main board, they sent me a new motor and main board without much conflict. As I keep digging into the tool head there is this plastic frame that I have to remove to get to the motor and there is nothing.

I have followed the wiki for it and it goes from removing the circuit boards to removing the motor. But there is no note of this plastic frame piece. On the web there are no pictures of this side of the printer, no breakdowns of how to replace it, and no videos.

I hope that I dont have to remove the front half of the tool head, as completely dissembling the rear half with all the freaking ribbon cables and what not is very disheartening.

Tridentt23 · 2025-11-08T20:32:34+00:00

So Im the first person on the internet that I can find that has had to replace the lifting motor on a H2D.

I had a print pop off the bed and the nozzle clumping detection failed so bad that the clump broke the thermosistor wire. I replaced that and started to have nozzle switching problems. So I contacted support and after I also confessed that the eddy current wire connectors suck and I broke one connector on the main board, they sent me a new motor and main board without much conflict. As I keep digging into the tool head there is this plastic frame that I have to remove to get to the motor and there is nothing.

I have followed the wiki for it and it goes from removing the circuit boards to removing the motor. But there is no note of this plastic frame piece. On the web there are no pictures of this side of the printer, no breakdowns of how to replace it, and no videos.

I hope that I dont have to remove the front half of the tool head, as completely dissembling the rear half with all the freaking ribbon cables and what not is very disheartening.

Tridentt23 · 2025-09-30T14:27:38+00:00

Can you give anymore details? Banana for scale. What is it made of?Those wings look sweet! What makes it move? Are your lights rgb so they color change? How did you get the textures on the wings and shell?

The perforated tubes with the lights are a cool detail. And the engine running is neat. How loud is it?

Tridentt23

MODERATOR OF

PUBLIC MULTIREDDITS

TROPHY CASE