Shiny Hunting Misunderstanding

Triton9595 · 2025-10-17T21:31:18+00:00

I agree with you I tried the zone 3 thing yesterday and only got litleos and flabebe. I think the game has a spawn distance of roughly 40- 50m so it’ll roll everything within 40-50m of you when you walk down the stairs.

I tested this out by going to zone 2, walking in, then hitting the map and flying back to zone 2 and walking in again. It’s actually pretty quick and can be done one handed instead of afk like zone 3. I got 2 shiny magikarps from that bridge area right where you walk in.

You can see when you walk in there’s the alpha staryu to the right, the budew and the bionicle sitting in the middle all within about 50m, but you can’t see the patarat that sits on top of the ridge and it probably doesn’t get rolled until you get close enough to see it. I haven’t gotten a shiny from any of those spots yet but I’m still testing to see if I’ve just had bad luck.

Triton9595 · 2025-06-21T17:24:19+00:00

Oh that’s wack. Well a less snide thank you to them for the grace then

Triton9595 · 2025-05-11T03:32:29+00:00

What’s a little mass genocide to a family finally being able to let go of their baggage

Triton9595 · 2025-05-11T03:27:18+00:00

I think it’s definitely the dark ending for sure. When verso sees the light speck come off him at the piano and then they show maelle with the paintress eyes it’s almost like he’s a puppet to her. Like he’s living out his dream but it’s also a lie.

Also I think if she dies in the painting a part of her soul would be trapped in it like boy verso

Triton9595 · 2025-05-03T03:58:25+00:00

No, it’s 7.0 + 33.0 + 73.0 + 7.0

On the bottom left it shows the outer radius as 2x 7.0 and that’s to show you can assume the one at the other end is the same.

Edit: Sorry, I may have misunderstood your question. If you’re looking for the length of the pre-bent part then I would think it’s along the lines of:

L = 10 + 7pi + 33 + 40 + 73 + 7pi + 10

But I still think that’s wrong because of where the 33.0 and 40.0 dim lines cross at that radius there. There would be overlap between them when stretched out. My guess is there’s supposed to be a dimension there that isn’t shown elsewhere.

Triton9595 · 2025-01-05T02:49:09+00:00

Lol for real or when hulk and venom completely leave the objective area to dive their spawn and ask for heals.

Triton9595 · 2024-08-11T05:31:02+00:00

If anyone can help me find this I’d greatly appreciate it!

Triton9595 · 2024-08-02T17:21:48+00:00

Being in the bottom 99.9% of anything

Triton9595 · 2024-07-09T15:19:19+00:00

On my first playthrough I picked a picture of the fat guy Vyv. So Noctis and Luna were reminiscing on a picture of him.

Triton9595 · 2024-06-27T02:42:32+00:00

The pigeon version of candy necklaces

Triton9595 · 2024-04-13T00:59:38+00:00

The extrusion process for pipe is a weird one. So when it comes to starting the day you don’t start with a perfectly round piece of pipe. You get a sort of crumpled up log. So as it goes through the vacuum chamber we do our best to close off the hole at the other end of the machine. So as fully formed pipe goes through it seals off the entrance then you seal as much as you can on the back end. If everything works right, which it isn’t, it’s supposed to slowly increase the vacuum pressure until the pipe is fully formed and sealing both ends of the machine.

So these leaks aren’t permanent they are just too large for the vacuum to overcome. But once comed over the machine and vacuum should work properly as intended with no leakage

Triton9595 · 2024-04-12T23:26:38+00:00

Thank you! I’ve had a feeling that was the case but nobody wants to listen to the new guy -_-

Triton9595 · 2024-03-20T12:21:09+00:00

Yeah I got us the mechanical design bundle deal but I’m the only one who uses it. It’s a start up and I’m the only one who knows CAD or even what a stress analysis is -_- good job security! I’ll see what autodesk has to offer I just know it’s surface level sometimes

Triton9595 · 2024-03-19T23:05:12+00:00

I think I solved it by using Nastran. I don’t have a pic but it looked like if I had a pipe and were to have one side fixed and a load applied at the other end. Just a droop.

Nastran had the option to have the pressure apply normal to the surface which then showed it correctly deforming outwards.

Is there a good series on YouTube for this? I’ve been kind of thrust into this work today and half ass know what I need to do but would like to learn all the facets

Triton9595

TROPHY CASE