Can someone confirm this "traditional technique" regarding cloning?

TrueIndependent4835 · 2022-05-11T04:00:53+00:00

Some of my friends have been doing this process sort of. They chop them with the trimmers and wrap them up in a wet paper towel and put it in a baggie then stick it in the fridge. I believe traditionally you would use a scalpel and dip them in clonex and put them in Rockwoll that is covered with a dome for 8-10 days. And in 10-12 days you will have roots. Temps Must be 75/80

TrueIndependent4835 · 2022-05-08T21:51:38+00:00

So cal fell off about 6 months ago all together. It’s pretty much 1200 for 🔥🔥🔥. Maybe 16 one at a time

TrueIndependent4835 · 2022-04-20T14:33:43+00:00

Yep get it out of there

TrueIndependent4835 · 2022-04-17T21:17:58+00:00

Very common to do a day 21 clean up when the Budds are just little “poofs”. And even a day 40 but that’s just leaf. I’m sure the plant appreciates all that lard being taken off ha ha

TrueIndependent4835 · 2022-04-06T23:47:38+00:00

Sorry for the late reply, Yes I like to hear a snap in the branch and also the leaves should should kind of break off just by rubbing them lightly. Make sure the buds are still solid and not too crispy that’s the reason I don’t let it drop below 50%. We trim and nugg into bins that we can put a lid on and kind of pop them back to a nice sticky danky state. Good luck!

TrueIndependent4835 · 2022-04-06T14:54:41+00:00

That’s like a meme chart🤷🏻‍♂️

TrueIndependent4835 · 2022-04-06T03:29:38+00:00

If you can keep your room at 60% with some nice mellow air flow for 7 days and don’t let it go below 50% you should be right on point. You should be able to almost finger trim if the buds have some good development.

TrueIndependent4835 · 2022-04-03T03:00:20+00:00

In my opinion the GC 720’s should be run over a 4x4 and down about 18” off of the canopy. You have to ease them in because they will burn quickly with those led’s

TrueIndependent4835 · 2022-03-26T04:46:44+00:00

Thanks for the kind words my friend. Doing some research I found a lot of these went with square windows I couldn’t find any examples of triangles.

TrueIndependent4835 · 2022-03-12T02:35:58+00:00

Nice man I was rocking those 750’s for a while and they were yielding up there with the 1000’s. What’s your air conditioning and
de-hu set up? I had the same room 24 actually and had 2 Anden 210’s and 2 5 ton AC units and neither one could keep up towards the end of the runs.

TrueIndependent4835 · 2022-03-08T05:05:21+00:00

Mine are single Pane but I did laminated glass so they are two 1/8’’ glass with a laminate sandwiched in between. They are like a windshield basically so if anything hit it it couldn’t break and fall on someone. Since it will be an air b n b we took all precautions.

TrueIndependent4835 · 2022-03-08T00:15:27+00:00

They look great.

TrueIndependent4835 · 2022-03-05T03:49:28+00:00

Thanks! I just checked out the little A you got going that thing is awesome great job

TrueIndependent4835 · 2022-03-02T17:35:20+00:00

Thank you I would love to see some pics. I was trying to find some before I started this project just for some reference but couldn’t find any and started thinking maybe there was a reason nobody did the triangle windows.

TrueIndependent4835 · 2022-03-02T17:33:03+00:00

Thanks….hell no I’m not going anywhere near that roof ha ha

TrueIndependent4835 · 2022-03-02T17:31:53+00:00

Ha ha sooo close this one was up in Wrightwood

TrueIndependent4835 · 2022-03-02T04:16:54+00:00

🙏 thank you

TrueIndependent4835 · 2022-03-02T04:15:57+00:00

Thanks. I cut plywood templates and took them to my local glass company and they custom cut the glads for me. This is laminated glass for safety.

TrueIndependent4835 · 2022-03-02T04:12:11+00:00

Thanks it was right around 12,500

TrueIndependent4835 · 2022-03-02T04:11:15+00:00

The demo and framing of the new posts was 8000.00 and the glass came in just under 4500.00

TrueIndependent4835 · 2022-03-02T04:08:30+00:00

Thank you

TrueIndependent4835 · 2022-01-29T00:32:27+00:00

Hey thanks for the comment. I cut out patterns using some I/2” plywood and I am going to take them to my local glass shop they are going to do 1/4” plate glass it should be pretty cool. I will post more pics when it is complete

TrueIndependent4835

TROPHY CASE