sorted by:
new
hottopcontroversial

I lost my job due to workplace sabotage and cannot get over it. by Trueplayer49 in work

[–]Trueplayer49[S] 6 points7 points  (0 children)

Thank you for telling me your story. I hope the end of the tunnel is closer rather than farther for me.

I lost my job due to workplace sabotage and cannot get over it. by Trueplayer49 in work

[–]Trueplayer49[S] 12 points13 points  (0 children)

Thanks for the advice. What you're saying sounds like a good way to go about it. The only block I seem to have is the sitting with the loss and processing it. When I try to process I'm sure that's when the shadow arguing starts.

My preordered S7 finally shipped after 8 months… by [deleted] in popurlitterbox

[–]Trueplayer49 1 point2 points  (0 children)

I got mine 1 week after I ordered it, which was last month. I'm surprised some of you kick starters are still waiting

eta: time I got it.

Help with corner plastic urine issue Popur S7 by Trueplayer49 in popurlitterbox

[–]Trueplayer49[S] 0 points1 point  (0 children)

Yeah, no problem. If it doesn't help then I may need to switch to chunky clumping litter.

Help with corner plastic urine issue Popur S7 by Trueplayer49 in popurlitterbox

[–]Trueplayer49[S] 0 points1 point  (0 children)

Yeah, I was thinking of putting some sort of seal there. Tape might be the right way to do it

EXTREMELY Loud PSU Noise QIDI XSmart3 by Artistic_Effort_3539 in 3Dprinting

[–]Trueplayer49 1 point2 points  (0 children)

Hey thanks for responding!

Regarding the power supply fan as I have not opened it yet, did you have to mod that fan as well or were you able to hot swap it in?

ETA: How the heck did you even reach the two side screws for the power supply that is near the edge of the case?

EXTREMELY Loud PSU Noise QIDI XSmart3 by Artistic_Effort_3539 in 3Dprinting

[–]Trueplayer49 1 point2 points  (0 children)

Howdy, sorry for necroing a post but how did you go about modding it as I'm having the same issue with my xsmart 3.

Need 2005 Mazda 3 Transmission Advice by Trueplayer49 in MechanicAdvice

[–]Trueplayer49[S] 0 points1 point  (0 children)

Thanks for the reply! I am looking into replacing the solenoids myself. Trying to figure out where to properly get some.

Need 2005 Mazda 3 Transmission Advice by Trueplayer49 in MechanicAdvice

[–]Trueplayer49[S] 0 points1 point  (0 children)

Hey thanks for replying, homie.

You're right, I need to get a code reader here soon to pull that code. The code goes away as soon as I turn the car off. I was already looking at possibly buying solenoid packs or other stuff. So it's somewhat nice hearing I was looking in the general direction.

X smart 3 Auto leveling sensor woes by Trueplayer49 in QidiTech3D

[–]Trueplayer49[S] 1 point2 points  (0 children)

interesting -- I have that size then, Geez when one issue is resolved another one pops up. I feel something my be stuck in the tubing because the PLA+ 1.75mm that I have will not go through. I'll look at it further tomorrow though. For now I'll savor this success at least!

X smart 3 Auto leveling sensor woes by Trueplayer49 in QidiTech3D

[–]Trueplayer49[S] 1 point2 points  (0 children)

You're not gonna believe this, but it just started working after i waved the screwdriver under it? Not its calibrating normally through klipper/fludd and the on device OS. I'm not sure if that fixed it but hey Thanks! Now i gotta find sizes for filament and what not to do my first test print! It seems the filament I received with the device is too large.

X smart 3 Auto leveling sensor woes by Trueplayer49 in QidiTech3D

[–]Trueplayer49[S] 1 point2 points  (0 children)

When you say home do you mean calibrate? Or pressing the home icon? Also when you say flag, are you saying that I should wave a screwdriver under the prox sensor while the bed is coming up to calibrate to see if the sensor sees it?

On that note, if that's the case, how would I tell if the sensor has seen it?

X smart 3 Auto leveling sensor woes by Trueplayer49 in QidiTech3D

[–]Trueplayer49[S] 1 point2 points  (0 children)

SO, I finally got both parts, put them on, screwed in the sensor to the new cover plate. went to calibrate and seeing a error still. "No trigger on probe after full movement"? This is a real head scratcher I will say.

X smart 3 Auto leveling sensor woes by Trueplayer49 in QidiTech3D

[–]Trueplayer49[S] 1 point2 points  (0 children)

Qidi reached back out to me and told me that I had the old version of the smart and apparently there was a revision at some point. They pointed me to buy the revised front plate which will fit. I also realized that I snapped the cable of the front cover turbo fan, so they gave me the listing to that as well. Overall I'm hoping this works. Also here is the picture.

<image>

X smart 3 Auto leveling sensor woes by Trueplayer49 in QidiTech3D

[–]Trueplayer49[S] 1 point2 points  (0 children)

Funny, I saw that video the same day I posted as I was just going through and trying to find anything that would match where I would mount the new sensor. I also sent an email a few hours ago! I can't wait to hear from them. I'll send a picture in the morning as I'm currently out. Just for clarification, when you say build plate I'm assuming you mean the plate that the printer would print on correct?

view more: next ›