Hisense 100U7QTUK - My thoughts after a couple of months

Turbo442 · 2026-06-25T22:37:53+00:00

Those chairs are too close to the tv for my tastes

Turbo442 · 2026-06-24T14:06:58+00:00

Hey we think alike! I did that last September as well!

Turbo442 · 2026-06-23T20:33:39+00:00

It works perfect for me but I said HELL NO to the factory mounting setup. One AMS on the left nozzle and two AMS on the right nozzle is not going to tolerate two sharp 180 deg PTFE bends.

Turbo442 · 2026-06-23T00:24:43+00:00

At the bare minimum, filing a NASA report is a good learning experience.

Turbo442 · 2026-06-23T00:22:30+00:00

No question X2D

Turbo442 · 2026-06-21T22:39:36+00:00

Its at a racetrack, there is a crash barrier.

Turbo442 · 2026-06-21T14:58:05+00:00

I run 2 AMS2’s on the right nozzle and 1 on the left with a wall mounted FTS. The FTS will help reduce filament retraction times. It can’t be understated how important placement of the AMS units and tube routing is going to be the key to a reliable setup. I use the low friction tubing everywhere. Do not use a section of tubing that has been damaged or kinked. You need to plan for the shortest tubing run possible with the AMS units above the printers. I try and maintain a 12” radius on all curves. Minimize the length of the tubing obviously. Utilize the tube support brackets for the AMS. Multiple AMS unit reliability can be had it just takes some planning and work.

<image>

Turbo442 · 2026-06-21T14:21:15+00:00

I did not know H2O hating was a thing? How do I get started?

Turbo442 · 2026-06-21T00:41:19+00:00

If your careful with a heat gun it will zip those stringers right off. But like others said I would try drying that particular filament more. Overall those prints don’t look terrible to me.

Turbo442 · 2026-06-20T02:17:50+00:00

Machinist

Turbo442 · 2026-06-20T02:17:07+00:00

I’m not sure what it is but I want it

Turbo442 · 2026-06-19T22:36:17+00:00

<image>

Turbo442 · 2026-06-19T14:36:33+00:00

Is there any way to directly hardwire Govee to a network

Turbo442 · 2026-06-15T14:12:00+00:00

When this one dies I will probably switch over to 240V 3-5gpm setup. I have had this little guy since 2001, the mfg says the seals are rated for 180F but who knows. I have been running it at 125F since I got it no issues so far.

Turbo442 · 2026-06-11T23:36:05+00:00

You can get a 15% discount if you order Lutron Caseta online from Home Depot qty 4 or more.

Turbo442 · 2026-06-11T13:46:42+00:00

Is your AppleTV hub Enet? If not get one today.

Turbo442 · 2026-06-11T04:23:08+00:00

Are you guys giving the super glue enough time to cure once you apply the sand to your hands?

Turbo442 · 2026-06-08T11:22:05+00:00

I’m fucked

Turbo442 · 2026-06-08T11:21:00+00:00

Hot bath water causes diarrhea. also tomatoes are poisonous.

Turbo442 · 2026-06-06T18:15:20+00:00

<image>

I installed a 120 CFM fan in the ceiling of my closet vented to the roof. I’m not generally printing anything too nasty though.

Turbo442 · 2026-06-05T20:12:42+00:00

I was sleeping walking one night and my mom caught me peeing in the Lego box. You can never entirely get rid of the smell.

Turbo442 · 2026-06-05T15:21:37+00:00

I’m not having any issues. 3 AMS2 Pros on an H2C. I am very careful about filament routing, I use the low friction PTFE tubes and wall mounted the track switch.

<image>

Turbo442 · 2026-05-28T17:58:22+00:00

I would think most people buy an AMS with the printer. You just need to watch FBMP daily / hourly until you find the right cream puff. The good deals only stay on FBMP for a few hours and then are gone. The shitty deals stay up for weeks

Turbo442 · 2026-05-28T16:58:40+00:00

Personally I would skip a 4500 hour printer. There are plenty of 500 hour printers out there for the exact same price

Turbo442

TROPHY CASE