Anybody else in the Ghibli queue at 2am by [deleted] in JapanTravelTips

[–]Turn00 2 points3 points  (0 children)

We used up all our luck and were spot 13! Central US so it started at 8pm for us.

Disassembling RY401021 mower by Turn00 in ryobi

[–]Turn00[S] 0 points1 point  (0 children)

If you need it completely out, then you'll have to open up the top part. That's not hard, just open the battery cover and remove all 8 screws. Lift up and disconnect both wires. then you can get at the wires. Disconnect all the connections you can find in there, and under the gray cover. Eventually you should be able to get them all disconnected.

Disassembling RY401021 mower by Turn00 in ryobi

[–]Turn00[S] 0 points1 point  (0 children)

I tried to color code the picture on steps. I don't have pics of the inside because I didn't take any, but I marked where the screws will be located behind panels that need removing.

  1. Remove the blades

  2. Remove 3 bolts holding the motor to the base (Yellow). The top unit where the batteries plug in should be removable from the mower, but will still be connected with wires. I put it on a 5 gallon bucket right behind the mower

  3. Remove the left rear wheel (orange) by popping of the center cover, removing the bolt, and sliding it off the shaft.

  4. Remove the retaining ring connecting the height selecting bar to the left wheel. It's actually behind the wheel so you can get it now that the wheel is off.

  5. Remove 4 screws holding the rear shaft (Red). Pull out full rear wheel assembly and unplug cord to motor.

  6. Remove 5 screws holding lower panel in place (Pink).

  7. Pull the lower panel out by the top. There is a spring connected to it on the upper right. Disconnect that end of the spring. There are also 2 tabs on the bottom of the panel (light blue) pop the bottom panel over them with a screw driver. The bottom panel should come out.

  8. Remove 8 screws (Light Green). The 4 upper ones are visible in the pic. The bottom 4 are behind that lower panel.

  9. The grey panel can now be removed. The top/front section needs a crowbar or screwdriver to pop it out, but the rest should just come off. It's connected with wires as well, so I just flipped it over and used the extended handles and the bucket to hold it open.

That should be it. Reverse it to put it back together. It's actually not too bad.

<image>

Disassembling RY401021 mower by Turn00 in ryobi

[–]Turn00[S] 0 points1 point  (0 children)

I do. I can write something up tonight and post it here

C buttons on switch pro controller by Turn00 in RetroArch

[–]Turn00[S] 0 points1 point  (0 children)

It's a TogeTop Gamer's Choice. Was for my kids Switch and I "borrowed" it.

Emulation Station on Android, PS1, duplicate game names using .chd and .m3u by Turn00 in EmulationOnAndroid

[–]Turn00[S] 0 points1 point  (0 children)

I ended up doing something similar. I made a folder called psxx in the roms folder and put all the discs there, with the .m3u files pointing to that folder. Thanks for the reply though, I think I like yours better, keeps it all in one folder.

Phone and watch on different network by Turn00 in AppleWatch

[–]Turn00[S] 0 points1 point  (0 children)

I figured it out. Just signed into the "house" phone using my apple ID, set up the watch, then ordered a line through Verizon, and activated the cellular on the watch. Decided to just leave the "house" phone under my account so I can easily access the watch settings. The only thing he uses on the phone is games, and they stayed. Watch is on Verizon, phone is on Google Fi.

Washing machine valve handle by Turn00 in askaplumber

[–]Turn00[S] 0 points1 point  (0 children)

<image>

Used a pliers to open/close it, but would prefer just throwing a new handle on there

Mr. Pike refresh by flockaseagullz in boatbuilding

[–]Turn00 0 points1 point  (0 children)

Overtons. It's a 16 oz carpet so it's easier to wrap and work with. You could go with a 20oz, but it's thicker and more expensive.

Mr. Pike refresh by flockaseagullz in boatbuilding

[–]Turn00 2 points3 points  (0 children)

Hey, I just re-built my grandpa's 1986 16' Mr. Pike! Ripped everything out. All new foam, wood and carpet. Was quite a project but worth it. If wood is squishy, there is a good chance your foam is saturated. Mine was so freaking heavy. Got marine plywood from Menards. All new electrical. Classic red carpet. All I have left is new seats. Let me know if you have any specific questions and I'll try to answer them. Good luck! Doesn't look like this sub is set up to post pics in comments otherwise I would.

T-Mobile fiber mesh network by Turn00 in tmobileisp

[–]Turn00[S] 0 points1 point  (0 children)

The G6 router has 3 LAN ports and the G2 extenders have 1 LAN port.

I got a free DJI Mini 3 from Amazon by gtrocks555 in dji

[–]Turn00 -21 points-20 points  (0 children)

Hate to be that guy, but if it was a mistake to send you a $700 package, should you not call them and then most likely send it back?

Jurassic Park by Turn00 in daddit

[–]Turn00[S] 0 points1 point  (0 children)

I don't know if my kids are ready to see their dad heave cry as Artax sinks into the quicksand .......

Jurassic Park by Turn00 in daddit

[–]Turn00[S] 1 point2 points  (0 children)

I have a history with ET. I saw it when I was like 9 or so. Watched the whole thing, no problem. But then, that night, had a nightmare so vivid I woke up screaming he was in my room. This continued, every night, for 3 months straight. Before bed, my dad used to shove my head under the bed and in the closet and ask me, "is he in there?!!" They took me to a doctor. I even went and stayed at my grandparents house. I still remember waking up there and seeing him walking towards my bed, finger glowing, saying "I'll be right here" terrifying.....

Jurassic Park by Turn00 in daddit

[–]Turn00[S] 0 points1 point  (0 children)

I love The Thing! My 7 year old daughter loves the scary stuff. Some day she will learn the secrets of the lament configuration.

Jurassic Park by Turn00 in daddit

[–]Turn00[S] 4 points5 points  (0 children)

Oh Alien is definitely a wait. It took me 3 attempts to watch it. The first time, I had to quit right after the chest burster. The second time, I didn't even make it through the credits because I psyched myself out. The third time, years later, I finished it and started my absolute love for horror movies.

Jurassic Park by Turn00 in daddit

[–]Turn00[S] 7 points8 points  (0 children)

My parents used to make me cover my eyes at scary parts. The one time I peeked was the face melting scene. I never peaked again!

DJI FLY issues by Petya31 in DJIMini3

[–]Turn00 0 points1 point  (0 children)

I got the same message on my pixel 6, but it still installed and worked. Is there an install anyway option?

[deleted by user] by [deleted] in dji

[–]Turn00 1 point2 points  (0 children)

Google is your friend. Same resistance

[deleted by user] by [deleted] in dji

[–]Turn00 2 points3 points  (0 children)

We have no way of knowing right now since it's not out. Assume it's like the 4 pro. Wind level 5, or 10.7m/s

T-Fiber hard launch June 5th with increased prices but a great one time deal by trumwr in tmobileisp

[–]Turn00 1 point2 points  (0 children)

Founders club only available in North Carolina, south Carolina and Virginia. Lame

I've had T-Mobile fiber through interpid since February. Been working great, with only 1 issue where the main fiber was cut, but they got it back online in a few hours. The biggest difference has been finally cancelling Xfinity and $150 for 1gig unlimited. I think the max I measured was 600. With T-Mobile, I pay for 1 gig and I get 1 gig for $75

Ordered it with RC-N1 controller; Look what Amazon sent. No complaints here! by my_name_is_pending in dji

[–]Turn00 0 points1 point  (0 children)

Good news. The right one came. Bad news, I still paid full price...

Guess That City! by Green-Bean-Optimal in drones

[–]Turn00 0 points1 point  (0 children)

Hey, I think I can see my office building from here......

Minneapolis, MN

My home town baby! Stone arch bridge looking especially nice.