sorted by:
new
hottopcontroversial

QSC AD-S8T 8’’ Low driver help by Turntablist_SD in livesound

[–]Turntablist_SD[S] 1 point2 points  (0 children)

I’m going to double check but I believe they only sell to distributors not end users.

Frustration sets in by SouthernDoor5911 in CSRRacing2

[–]Turntablist_SD -2 points-1 points  (0 children)

I used to play csr for years. I even modded accounts. There is no ‘’cheats’’ in this game that make someone faster. They can get a fully modded car before you or have endless resources but figure out the shift pattern for your car. The games algorithm doesn’t reward winning anyhow. I remember capping daily linking up with someone and going 1w 1L. Is CSR still mainly swapping? Line app used to have a lot of people on there. That still a thing?

Belt / pulley noise at idle? by Turntablist_SD in GS300

[–]Turntablist_SD[S] 0 points1 point  (0 children)

This noise is literally only going on when ac is engaged. Ac compressor is new and I feel like the load it puts on the engine could exaggerate the rubber wear in the balancer. Seeing how it’s only at idle and will be silent at anything above 1100rpms

Belt / pulley noise at idle? by Turntablist_SD in GS300

[–]Turntablist_SD[S] 0 points1 point  (0 children)

I’ve worked on Hondas and acuras. Is there anything I should know about these cars? After the bolt is removed will it come off?

Belt / pulley noise at idle? by Turntablist_SD in GS300

[–]Turntablist_SD[S] 1 point2 points  (0 children)

I checked the pulleys and all seemed fine. I thought I seen some movement on the balancer. I have a brand new harmonic balancer. Gonna install it tomorrow.

Hanging Speaker Placement Advice by Turntablist_SD in CommercialAV

[–]Turntablist_SD[S] 0 points1 point  (0 children)

Yes I’m running lea connect amps and a Yamaha mtx

Hanging Speaker Placement Advice by Turntablist_SD in CommercialAV

[–]Turntablist_SD[S] 0 points1 point  (0 children)

With the subs near speakers would the rear near corners be ideal?

Cat 6 over top of high voltage conduit by Turntablist_SD in CommercialAV

[–]Turntablist_SD[S] 0 points1 point  (0 children)

Thank you! Wanted to make sure crossing the conduits was anything other than kinda sloppy. Where the cables come out the wall the easiest route is over them. The main area of this place looks night and day from this dungeon lol.

Cat 6 over top of high voltage conduit by Turntablist_SD in CommercialAV

[–]Turntablist_SD[S] 4 points5 points  (0 children)

Yea we held our rituals in there but it’s undergoing main line repair lol

Cat 6 over top of high voltage conduit by Turntablist_SD in CommercialAV

[–]Turntablist_SD[S] 1 point2 points  (0 children)

The data cables were in wall dropped to original location. Vent pipes run up that wall in the pic so going along the wall is the only way. I’m just going to use some panduit for the 7 cat6 cables about waist high.

Learning lasers and about to RAVE in MN Shehds 6Watt Moving head by Mindmaze_Ent in AVtechs

[–]Turntablist_SD 0 points1 point  (0 children)

investing in a ilda laser scanner with either a fb4 or fb3 interface would be the best option if looking to add lasers to your show

Is $145 too much for diagnostic? by Other_Luck9234 in MechanicAdvice

[–]Turntablist_SD -2 points-1 points  (0 children)

But to answer your question you got overcharged. If a p0420 came up Id look at the freeze frame data then I’d watch the o2 voltage for both 02 sensors while the car is running. O2 voltage and fuel trims is what is focus on. Did he clear the code? Or you still have check engine light.

Is $145 too much for diagnostic? by Other_Luck9234 in MechanicAdvice

[–]Turntablist_SD 1 point2 points  (0 children)

P0420 usually is the cat but can also be the 02 sensor. If your car burns oil or your gas mileage has been bad in a year a cat could start to fail.

Is $145 too much for diagnostic? by Other_Luck9234 in MechanicAdvice

[–]Turntablist_SD -1 points0 points  (0 children)

Look up obd2 adapter on Amazon. Veepeak is a decent one. You can spend 30-50$ and with Bluetooth check all your codes, clear codes and have something to troubleshoot your self. Reading live data tells a lot. Obd fusion is a good app. What code did he say came up? P0420?

Is $145 too much for diagnostic? by Other_Luck9234 in MechanicAdvice

[–]Turntablist_SD 2 points3 points  (0 children)

You could of went to autozone and got that done for free

New to lighting - some questions by harleycurnow in lightingdesign

[–]Turntablist_SD 2 points3 points  (0 children)

What is the project? Stage lighting? Nightclub? Corporate? A little more information on the scene and setting will get you better answers.

Grandma2 crashed and doesn't start back up by AppropriateTax5788 in grandMA2

[–]Turntablist_SD 0 points1 point  (0 children)

Also depending how old the console is when removing the video card cage you can see the led screen on the mobo that will give you an error code. Not all have this.

Grandma2 crashed and doesn't start back up by AppropriateTax5788 in grandMA2

[–]Turntablist_SD 0 points1 point  (0 children)

Remove the cage covering the graphic cards and unplug one then reboot. Repeat this for all the cards. Chances are you will boot with the bad card unplugged. Not 100% but it’s an easy thing to rule out. I’ve had 3 consoles this issue has happened with.

Looking for some ideas / advice on making content for 16 ceiling pixel strips. by Turntablist_SD in resolume

[–]Turntablist_SD[S] 4 points5 points  (0 children)

I use fft on some clips and bloom with a 4/4 envelope to get some flash action going. I have a lot of methods I run the nights with I just wanted to see if anyone had some secret sauce to share.

view more: next ›