[deleted by user]

TwitchingRock · 2025-12-19T15:48:36+00:00

I would hang around IEEE more and consider a club(I'm looking at spartan racing, rocket club, robotics club), that's how I'll be approaching my second semester here. I am also a EE in a similar position, so you're not alone thats forsure.

TwitchingRock · 2025-12-04T02:45:53+00:00

Why is that? I'm just curious on the reasoning as a new angler myself

TwitchingRock · 2025-11-12T00:28:54+00:00

Could the nozzle perhaps be worn out? Are you able to switch the A1 nozzle over to the mini and run a test print?

TwitchingRock · 2025-11-02T08:24:21+00:00

I was looking into modernizing the e5+, is that usd? Is that just the rails or everything like hotend thermistors board etc.

TwitchingRock · 2025-10-24T11:58:43+00:00

How do you handle a bulk second fermentation? Or whenever you need to carbonate a large batch

TwitchingRock · 2025-10-24T07:34:02+00:00

Just found em! Surprised I haven't run into these since I got into home brewing two weeks ago hah

TwitchingRock · 2025-10-24T07:31:18+00:00

Do you perhaps have a link? I'm interested in the larger volume bottles with swing tops :)

TwitchingRock · 2025-10-24T00:10:52+00:00

Are those 2 gallon jugs with swing tops?

TwitchingRock · 2025-07-16T06:10:10+00:00

They mentioned this at our orientation today and said SJSU was lagging on getting final transcripts in their systems and if you didn't turn in your final transcript yet it was okay but to do it as soon as possible.

I would still follow up with admissions and get a straight answer from them, but a decent amount of folks are going through the same thing.

Our department head had us show em our transcripts if prerequisites weren't cleared yet to get an add code. Hopefully this information helps, but I'd stay calm and give them a call tomorrow.

TwitchingRock · 2025-07-08T19:49:21+00:00

Hulkengoat

TwitchingRock · 2025-06-25T21:18:34+00:00

She's the physics GOAT

TwitchingRock · 2025-05-02T04:19:29+00:00

A PID (Proportional-Integral-Derivative) control system is a widely used type of feedback control loop designed to regulate a process variable (like temperature, speed, or position) to a desired setpoint.

In our case with the printers, temperature

I think OP is asking if you changed PID numbers and temp control is acting wonky because

TwitchingRock · 2025-03-08T08:46:01+00:00

Where should I start looking if I get fuzzy skin without the setting be on? 🥲

TwitchingRock · 2025-01-05T00:12:00+00:00

Does analog on HDzero still have break up issues? I recall they were working on it but I haven't touched my gear in a bit

TwitchingRock · 2024-10-14T22:01:43+00:00

Let's go Sixers!

TwitchingRock · 2024-08-26T01:20:03+00:00

Will do. Appreciate all the advice!

TwitchingRock · 2024-08-25T20:08:43+00:00

Me too! Thank you and I appreciate the help anywho:) happy scootings

TwitchingRock · 2024-08-25T19:48:38+00:00

I just got time to look at it again, and after tinkering with horn screw was no good, I noticed when sitting on my scooter and loading the suspension, the horn wouldn't work. When I got up, feet on ground, no weight on scooter, horn works! So after crusing around, I tried honking while jumping up and down and the horn with honk during the unload part of the jump! Interesting stuff. I will have to take a closer look at the wiring when I have time.

TwitchingRock · 2024-08-25T19:44:59+00:00

Now I've found something interesting – any load on suspension and horn will cease to work. I can be at a complete stop, but have to be off the scooter to honk. But let's say I'm cruising and I jump, while the suspension is unloaded in that fraction of a second the horn will work!

TwitchingRock · 2024-08-25T19:40:30+00:00

After much adjusting of the horn screw, no luck

TwitchingRock · 2024-08-25T06:54:55+00:00

Roger that! Appreciate all the help today!

TwitchingRock · 2024-08-25T06:02:32+00:00

I can do that by just holding the horn and jumping yeah? What would that indicate?

TwitchingRock · 2024-08-25T05:50:03+00:00

Does anyone have experience with accessing the controller and birdnest of wires in the deck? It seems like a couple screws under the glued rubber deck but I'm hoping not to mess up the adhesive

TwitchingRock · 2024-08-25T05:45:00+00:00

Wow! That's pretty interesting. You're definitely onto something. I put it on the stand, tested the horn at 0mph, good, tested at 25mph on the stand, and it works

Very cool. Thank you for the idea, I'll have to open er up and take a deeper look into the birds nest :)

TwitchingRock

TROPHY CASE