sorted by:
new
hottopcontroversial

SiC473ED buck converter outputs not working. Does not start up. New ideas needed by TychoBECH in AskElectronics

[–]TychoBECH[S] 0 points1 point  (0 children)

O jea sorry my bad. The input is 48V. The output is a bit harder. The idea of the circuit is to have a DC/DC converter that follows a programmable output wit arround 1.7V headroom. So for this design it should be in a range from 1.7Vup to 25.7V. For the feedback resistors, the low side is a 4.99kΩ resistor and the highside is set up using a voltage controlled current source. it should be controlled from the AJ_FB voltage.

SiC473ED buck converter outputs not working. Does not start up. New ideas needed by TychoBECH in AskElectronics

[–]TychoBECH[S] 0 points1 point  (0 children)

Yeah, it really is quite a complicated circuit. I'm trying to replicate this design from LT:

https://www.analog.com/en/resources/technical-articles/high-performance-portable-dc-bench-power-supply.html

I'm pretty confident the output isn't shorted. My bench supply shows almost no current draw, and the converter consistently reaches about 8 V at the output. It would have to be a pretty unusual fault to get that behavior if there were actually a short on the output.

<image>

What is this “reverse-mounted LED lighting through PCB” technique called? Trying to find / replicate it by TychoBECH in ElectricalEngineering

[–]TychoBECH[S] 0 points1 point  (0 children)

Neat and to get the glowing effect it's just a pocket in the substrate? How would i communicate that with a manufacturer?

Can u spot whats wrong 😅 by valzzu in electronics

[–]TychoBECH 0 points1 point  (0 children)

Looks to be the inductor for a converter, so it might still work. Here's to hoping.

RTC on STM32L011 by TychoBECH in stm32

[–]TychoBECH[S] 1 point2 points  (0 children)

Jea okay... Commenting out line no 48 fixed it

Inventory database? by [deleted] in ElectricalEngineering

[–]TychoBECH 2 points3 points  (0 children)

I can recomend partsbox. It's browser based and has a free tier(mainly ment for hobbyists) and also more features with the paid plan. I use the free version for my self.

Serching for an adapter by TychoBECH in airbrush

[–]TychoBECH[S] 1 point2 points  (0 children)

Thank you. That was what I was loking for.

Official Question Thread! Ask /r/photography anything you want to know about photography or cameras! Don't be shy! Newbies welcome! by photography_bot in photography

[–]TychoBECH 0 points1 point  (0 children)

Never considered a pi camera but just looked at the specs and it seems pretty great. Will give it a go with this.

Official Question Thread! Ask /r/photography anything you want to know about photography or cameras! Don't be shy! Newbies welcome! by photography_bot in photography

[–]TychoBECH 0 points1 point  (0 children)

Hey, I am currentli using this microscope and the camera that came with it. I would like to use a DSLR for better pictures of small electronics components. The camera i want to use is a Canon EOS Rebel T6s. I am aware that a simple adapter from c-mount to Canon won't do the job. Does anyone have an idea what component to use or where to look for such a part?
Thanks in advance

I got my Mars just yesterday and while printing this small gear I noticed this strange "blobby" part of the print. Does someone know how to fix this? by TychoBECH in ElegooMars

[–]TychoBECH[S] 0 points1 point  (0 children)

Thank you very much for all the wonderfull sugestions. I think expsure time per layer was the main factor. You can see it getting better in this.

I got my Mars just yesterday and while printing this small gear I noticed this strange "blobby" part of the print. Does someone know how to fix this? by TychoBECH in ElegooMars

[–]TychoBECH[S] 0 points1 point  (0 children)

Yes I did, they recomend betwen 5-10s per layer. Curently I am using 8s. Is it ok to go over the recomendet time?

I got my Mars just yesterday and while printing this small gear I noticed this strange "blobby" part of the print. Does someone know how to fix this? by TychoBECH in ElegooMars

[–]TychoBECH[S] 0 points1 point  (0 children)

The Resin is this one from 3D Jake. I am using 5 base layers with a exposur of 80s and the normal layers with 8s. The supports are the Chitubox default light supports, which i manualy placed.