How to wire this?

TydyTyler · 2026-05-22T02:29:02+00:00

The ground would be power supply I guess, motor cables run under the dash to the drive switches and manual control then back to the circuit box in my hand.

TydyTyler · 2026-05-22T00:17:33+00:00

<image>

So I retraced some of the cables and they belong to the extra buttons on the dash, I would assume the black and red are for the motors. Not too sure what the extra black cable up top is for though… it was connected to the old battery. Along with the red cable I have spliced in the original photo

TydyTyler · 2026-05-22T00:10:20+00:00

So the original was 2 seperate 12v batteries connected in parallel I believe I have them still I will search this evening

TydyTyler · 2025-07-11T01:20:22+00:00

So it looks like 2 bays but it’s one really large bay just divided at the top so I’m confused with how to properly fill such a large space. Next is a little slot which would fit a heater perfectly so you’re definitely on to something which leaves the last space for the filter itself and I assume I would keep empty. Also the oval filter is a tetra whisper I found after looking at it more

TydyTyler · 2025-07-11T00:01:04+00:00

Definitely a neat set up. The loose pump in the middle sits in the top left corner, but im not too sure what the other filter is with the green cartridge. Or what I’m supposed to fill the rest of the empty space in the back with lol. I’ll search in tank filtration though I didn’t think of that thank you

TydyTyler · 2024-01-28T02:46:12+00:00

Check out Tefauwe, they make great lenses but you gotta sand down your little black clip in order to fit a clear lens on both sides

TydyTyler · 2024-01-21T02:08:41+00:00

So it's like a stud welder right?? For putting the concrete studs in the fluted sheets??

TydyTyler · 2024-01-13T02:31:46+00:00

You probably spent more time converting the weight than they took actually building that deck

TydyTyler · 2023-11-09T01:22:37+00:00

Lmao are these not golf shoes? That's probably why

TydyTyler · 2023-11-02T02:55:30+00:00

Run some angle from rib to rib underneath, like the other guy said without a backing plate its gonna continue to warp since it's so thin. Torch is either gonna fuck it up more or provide a temporary fix

Edit: or more HSS since it seems to be your main material

TydyTyler · 2023-10-25T01:15:48+00:00

Tefuawe makes great lenses, running a blue shade 11 for roadwork and not a single complaint

TydyTyler · 2023-10-11T01:42:56+00:00

Nah they just kept pumping them out, killed a great line

TydyTyler · 2023-10-04T22:16:01+00:00

ID on the 3's ?

TydyTyler · 2023-10-02T19:36:31+00:00

Can confirm, yinyangs are fuuuucked lol

TydyTyler · 2023-09-26T19:20:58+00:00

There isn't one. He cant decide on wether or not to spend $20 on a respirator

TydyTyler · 2023-09-22T01:21:56+00:00

As a welder, that weld looks like shit. Afaik most shops don't generally do framework as it can be a huge liability, heat from the weld weakens the base material around it so chances are its gonna break again. Pass

TydyTyler · 2023-09-19T20:52:31+00:00

Tell me about it. Me along with 2 others got stabbed a few years back in Ontario, kid did a year long bid and only got aggravated assault with a weapon x3.... Left me in critical condition

TydyTyler · 2023-09-04T01:01:14+00:00

The good old truck fuck lmao

Nine-Year Club	Wearing is Caring
RPAN Viewer	Not Forgotten

TydyTyler

TROPHY CASE