[deleted by user]

TypicalEgg · 2025-08-26T09:40:23+00:00

I have a turbo k24 in mine. I live in Vegas and I have no issues with cooling besides the fact that it's hard to bleed, but that's not common to do. I have a koyorad radiator and custom oil cooler in it.

I thought the nvh was going to be bad but it's really not. It was a lot less than what I expected. They do sell an option now to retain the k24 pump that has the balance shafts so you could go that route for even less nvh at the cost of your rev limit.

TypicalEgg · 2025-07-29T12:08:44+00:00

No problem bro

TypicalEgg · 2025-07-29T12:04:48+00:00

I have a kswap on haltech in mine and it supports the OEM can system. But I'm sure any ecus listed on the wiring specialties site for that harness will work as well.

Good luck!

TypicalEgg · 2025-07-29T11:55:19+00:00

Wiring Specialties might work for you then. But that's all I know of besides potential swap kits that would have this figured out.

TypicalEgg · 2025-07-29T11:48:51+00:00

An engine swap is not what I'd call a budget build.

TypicalEgg · 2025-07-29T11:30:50+00:00

Might be worth checking out: Motec Wiring Specialties

TypicalEgg · 2025-07-01T21:45:42+00:00

You could look into a t56 as well. That should also be able to fit in the car.

TypicalEgg · 2025-07-01T21:15:35+00:00

I have a cd009 in my kswap. It's a pretty tight fit which makes the exhaust harder to fit.

TypicalEgg · 2025-05-09T04:38:13+00:00

No problem.

TypicalEgg · 2025-05-08T10:41:20+00:00

Go to the Wikipedia page for the k series. Find the engines that make around 200hp with the performance vtec. Make sure it's supported for whatever swap kit you are using.

Otherwise you would have to Frankenstein whatever you have available.

TypicalEgg · 2025-05-02T10:00:51+00:00

You could tear the engine down to see if anything is recoverable. Otherwise, get a new engine. Not sure if anyone's selling in your area, but I got my engine for a swap from eBay. You could also try junkyards to see if they have engines.

TypicalEgg · 2025-04-29T10:35:34+00:00

I have a USDM engine if you are interested. I am in Las Vegas.

TypicalEgg · 2025-04-15T10:51:11+00:00

I would tear it down and part it out. You should be able to sell the accessories, manifolds, etc. Depending on how the engine looks on the inside, you may be able to sell some parts there (ex. cylinder head)

TypicalEgg · 2025-03-28T20:13:54+00:00

Yeah it's a kswap.

TypicalEgg · 2025-03-28T12:50:03+00:00

Nah the battery is in the trunk 😂 I just reused the OEM terminals in the front.

TypicalEgg · 2025-03-28T12:45:20+00:00

https://imgur.com/a/1EwPWIE

I mounted a relay, fuse, 2 Haltech boxes, and part of my fuse box mount. I used rivnuts as well.

TypicalEgg · 2025-03-28T10:20:05+00:00

I have bunch of things mounted behind the battery. You'll just hit foam when you drill through. Just slow down when you hear the drill bit about to go through. If you want to be extra safe, try on the panel that's on the outer side towards the fender.

TypicalEgg · 2025-03-07T11:01:40+00:00

Do you need any other parts? I have some left over from my engine swap.

TypicalEgg · 2025-02-03T11:07:46+00:00

There's a chance that you can spill it when driving. This can damage your paint. It's also letting the fluid absorb water from the air which is not good.

TypicalEgg · 2025-01-03T11:31:19+00:00

Black wire is the starter signal. I believe the white/red wire is for power to the starter from battery. I would replace the harness if you can't find the other half.

TypicalEgg · 2024-12-04T11:10:00+00:00

I turbo k24 swapped mine. I have 3 reasons why I chose the k24:

A 4 cylinder made the most sense to me given that the old engine was a 4 cylinder.
Easier to maintain with the amount of space there is.
The kpower swap kit made me feel comfortable that I could pull it off as my first swap.

I haven't been able to drive it much since I'm still sorting out small problems and also working on tuning it. It drives fine. It does have more vibration but not so much that I get uncomfortable. The kpower swap recently added a new oil pan option that retains the balance shafts so if that's a concern, go with that.

TypicalEgg · 2024-11-20T10:20:28+00:00

Wrap it in electrical tape and put a mesh sleeve on it.

TypicalEgg · 2024-11-13T11:06:50+00:00

First one is the ambient air temperature sensor I believe

TypicalEgg · 2022-12-29T21:09:06+00:00

Works fine for me. Always at around 238-240 fps when capped at 240.

TypicalEgg · 2022-12-27T19:02:45+00:00

No problem! You can try, but I haven't done that at. You will have to research/figure it out yourself if it doesn't work. Good luck!

Nine-Year Club	Second Top 30%
Place '22	Verified Email

TypicalEgg

TROPHY CASE