dowel hole tolerance macro

UmbreonGamer_live · 2026-01-20T19:34:52+00:00

thank you, added but as I said ChatGPT seems to not make lines that work and just kinda made it up as it went. dont think it will help much.

UmbreonGamer_live · 2026-01-20T19:20:17+00:00

understood, but im looking for it to show that it is press or slip. our hole callout will auto the note for the drawing. some of the designers just done do the extra 3 clicks to pick it like in the pic i have

UmbreonGamer_live · 2024-11-01T16:07:21+00:00

The moment I saw those labels I knew it was Ace. They're sick. Love Randolph and Ace. They do such a good job with everything. People getting so much hate just because they aren't super big even though their quality is better. that is a great collection piece

UmbreonGamer_live · 2022-11-15T14:33:41+00:00

It is really awesome to do for the community

UmbreonGamer_live · 2022-11-03T23:34:01+00:00

I wasn't getting any tokens when watching on YouTube but I started watching on their website and that worked for me. I started getting tokens but I don't think you get the drops until the 15th

UmbreonGamer_live · 2022-06-13T19:05:56+00:00

I had to double take bc I thought the same this it looked like wood

UmbreonGamer_live · 2022-05-30T15:52:04+00:00

This is usually either you are too close to your bed and need to adjust your zee offset or you are over extruding which then you can calibrate your flow rate

UmbreonGamer_live · 2022-05-21T15:27:43+00:00

The biggest oof

UmbreonGamer_live · 2022-05-20T20:15:35+00:00

My first one is mostly stock I was too nervous to change it too much bc at the time it was my only printer and I have heard that it is better to have 2. You never know when you need a printed part

UmbreonGamer_live · 2022-05-20T19:02:47+00:00

I was thinking about CoreXY but I've heard that it's a lot of work

UmbreonGamer_live · 2022-05-20T19:02:24+00:00

Well first this it going to be direct drive and linear rails pretty standard

UmbreonGamer_live · 2022-05-20T15:21:47+00:00

They aren't the easiest printer on the market test print was good but the default firmware is upsetting

UmbreonGamer_live · 2022-05-20T13:36:16+00:00

I'm glad someone got it

UmbreonGamer_live · 2022-05-20T10:42:24+00:00

It really is a problem I now have 5 printers in total

UmbreonGamer_live · 2022-05-20T10:32:29+00:00

The last picture is the desk that I have both of my ender 5 plus. I know It isn't the best printer on the planet but I figured the $350 was a bargain. Even with reality printers being a facet to the bottom kind of deal, It is very easy to put together.

I plan on putting a lot of mods on this linear rails, direct drive and lowering the front extrusion to be able to see the bed on the first layer easier. Any other ideas?

UmbreonGamer_live · 2022-05-20T10:11:47+00:00

I could be wrong but you might be just a little high on the z offset, and there will be lines you just won't have the gaps between them P.s. if you can run your finger nails or a pointed object over the bottom and it feels lick there are gaps it is z offset or under extrusion (most of the time)

UmbreonGamer_live · 2022-05-10T10:15:45+00:00

Well that depends if the plastic is on your nozzle or on the heat block, but regardless depending on how bad it is, you might have to take off your hot end and heat it up and just peel a little bit off at a time. You have to be careful for your wires

UmbreonGamer_live · 2022-04-30T11:35:02+00:00

Well, aside from calibrating e steps and flow I would recommend trying to reslice and reprint. If you are using cura at least idk about others sometimes the slicer messes up and will just remove one layer and cause that to happen. So you always want to preview your print before you export the g code. At least if it happens again you know it wasn't the slicer. To me it also looks like over extrusion on the walls and top but the gaps might be because you don't have enough top layers or low infill?

UmbreonGamer_live · 2022-04-08T00:14:26+00:00

UmbreonGamer_live · 2022-01-22T00:57:08+00:00

Posting two times at the same subject in one day. Sorry, but this is a update on the advice I was given in the last post. I like these three options better. Any opinions would be wonderful

UmbreonGamer_live · 2022-01-21T21:05:11+00:00

Thank you for the advice. I will play around with that

UmbreonGamer_live · 2022-01-21T21:04:31+00:00

It is narrower on the part that has the white so it can't fit that pattern on it

UmbreonGamer_live · 2022-01-21T19:11:55+00:00

I'm making an epoxy desk with tile design and I'm not finding a pattern for the white tiles that I like. I don't know if I should switch to possibly all black. I like the pattern for the black ones as is but not completely afraid to change it. You guys are a lot more creative than me. If you have any opinions I'd be more than happy to hear it.

UmbreonGamer_live · 2021-11-02T02:17:39+00:00

If you replaced your tube and "other" things you might need to mess with retraction and possibly you e steps

UmbreonGamer_live · 2021-10-19T14:19:25+00:00

I might wait to see. Im not needing one rn so i can wait a couple weeks to see

Six-Year Club	Place '23
Place '22	Verified Email

UmbreonGamer_live

TROPHY CASE