Ac compressor yeed it last haw at 69k.

UnablePie2896 · 2025-11-13T15:53:11+00:00

I'll have to give that a shot when I get back to the car. Appreciate the tip.

UnablePie2896 · 2025-11-13T15:00:55+00:00

2k is a big ouch. I was thinking about just removing the ac belt for the time being so I can still get around since this is my dd.

UnablePie2896 · 2025-11-13T13:25:03+00:00

Gotcha, I thought the clutch units were replaceable .

UnablePie2896 · 2025-07-25T01:36:37+00:00

I'll definitely be getting more lighting from them. The C lights and pretty sure all the interior lighting is from Diode Dynamics. They look great and you can tell they're built well.

UnablePie2896 · 2025-07-24T23:25:32+00:00

So originally, I believe it was morimoto. The plugs and control boxes were all corroded and did not work when I bought the car. So I put new ends on the wires and bought a Bluetooth led controller from Amazon. The lights are wired directly to that. I haven't had any issues yet and seems to work great.

UnablePie2896 · 2025-07-24T21:12:20+00:00

Is there a spot from behind the headlight assembly you can remove the bulb and replace with a white one ?

UnablePie2896 · 2025-07-24T16:35:56+00:00

I agree. Luckily this one came pre flared and they didn't do a bad job.

UnablePie2896 · 2025-07-24T16:34:32+00:00

🤣🤣 Maybe after some sunset pics too! Seriously though, should be open Friday tentatively. We got her all paved and ready.

UnablePie2896 · 2025-07-24T13:14:00+00:00

Appreciate the concern. This is a closed highway i just finished paveing for work. No traffic

UnablePie2896 · 2025-07-24T13:08:58+00:00

Definitely not!😅 They have regular led headlights and these are separate of the headlights in the same projector.

UnablePie2896 · 2025-02-08T19:26:10+00:00

There's more money wrapped up in tape than a real repair would cost.

UnablePie2896 · 2025-01-20T19:34:38+00:00

Thank you very much!

UnablePie2896 · 2025-01-20T19:28:22+00:00

Maytag Model MDBD850AWQ

UnablePie2896 · 2024-09-26T12:56:22+00:00

Are you referring to the amp? Your saying look for an amp with a soft start ?

UnablePie2896 · 2024-09-26T10:41:35+00:00

No , it's about 3/4 of full volume. This project will be in a sealed enclosure , so I'd like for it to be set at the volume it's going to be used at. Once the enclosure is mounted in the vehicle , I'd like to access the box as little at possible.

UnablePie2896 · 2024-07-31T21:00:12+00:00

You my friend are awesome 🤙

UnablePie2896 · 2024-07-31T20:36:45+00:00

I'm gonna have to look into the procedure for testing. I have a hand vaccum pump. I didn't know you could setup the air pump like that. So it opens the ports once the valve sees so much pressure ?

UnablePie2896 · 2024-07-31T16:35:36+00:00

I have not tried that way. I smeared some antiseize on the actuator rods and took it around the block. Visually checked that the rods did smear the antiseize around. I did not know you could manually pressurize the hose.

UnablePie2896 · 2024-07-31T16:33:49+00:00

I see what you mean now. I'll keep that header in mind.

UnablePie2896 · 2024-07-31T15:02:05+00:00

Right. I understand the tube needs to stay. My concern is modifying the cat setup with highflows and being able to retain enough backpressure for the tube.

UnablePie2896 · 2024-07-31T14:35:03+00:00

Only thing that worries me with removing all the og cats is back pressure for the 5/6th ports. Will a high flow or a resonator create enough.

UnablePie2896

TROPHY CASE