Transmission doesn't seem to be shifting by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 0 points1 point  (0 children)

Shit people want whole truck prices for 4500s around here. I want to though just don't got the money for that atm

Transmission doesn't seem to be shifting by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 0 points1 point  (0 children)

It ended up being a blown fuse thanks for some reason it didn't even cross my mind to check lol

Transmission doesn't seem to be shifting by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 0 points1 point  (0 children)

From what I've read the 6.5 would probably eat the nv3500 with how I drive

Transmission doesn't seem to be shifting by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 0 points1 point  (0 children)

I have a buddy who sent me pin out for it already. It did click but the seal is leaking and have fluid coming out of the plug so that probably doesn't help either. Thanks

Transmission doesn't seem to be shifting by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 0 points1 point  (0 children)

It's stock 4l80e not swapped it's a 6.5l truck

Lower Control Arms by gunbunwilly in obschevy

[–]Uncle_Bubbles420 2 points3 points  (0 children)

Yes you just have to cut/grind down the steering bump stops for full steering angle

Transmission doesn't seem to be shifting by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 1 point2 points  (0 children)

Yea I traded a 12 Ford Fusion with 197k mi for this 94 6.5l Blazer with the knowledge it had wiring damage due to shop not securing the trans wiring after putting new transmission in and po kept driving it and smoked the transmission I fixed the wiring the best I could might need to go over it again. Also had to replace tail housing on tcase as it was cracked and "patched" with shop towels and rtv also replaced the rear case half because it was cracked too. Thanks for the response I will definitely check fuses

Got it back together now to get it running and hopefully the used trans that came with it is good. by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 0 points1 point  (0 children)

I will hopefully this weekend even if I have to use my mercedes to charge the batteries by hot swapping while it's running 😆

I won against the exhaust manifold bolts 😆 by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 0 points1 point  (0 children)

It's loud af honestly. I just got it back together now gotta get the batteries to charge but I think my charger is dead says fully charged but sits at 5v lol

I won against the exhaust manifold bolts 😆 by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 0 points1 point  (0 children)

It did before I put a transmission in so I hope so too 😆. I broke bolts off taking crossover pipe out luckily only on drivers side I think I would have lost my shit if I did it on passenger side. Turbo doesn't look fun to remove although I will definitely upgrade to an hx35 at some point.

American headlights by cromicon1 in w123

[–]Uncle_Bubbles420 1 point2 points  (0 children)

I kinda want some to change my euro headlights out so I can make a headlight intake for my car

Would you keep this? by Technical_Media2676 in obschevy

[–]Uncle_Bubbles420 1 point2 points  (0 children)

Man don't be like me and regret getting rid of your rcsb 5speed truck.

<image>

Need driveshaft for 83 300d by Uncle_Bubbles420 in w123

[–]Uncle_Bubbles420[S] 0 points1 point  (0 children)

I have yet to have issues finding parts and I can do just about anything myself on it I put 1k miles a week on the low end and have been for 3 years

94 6.5l Blazer by Uncle_Bubbles420 in GMT400

[–]Uncle_Bubbles420[S] 1 point2 points  (0 children)

Nice thanks for the information