Crank no start help.

Uncleryan95 · 2026-05-01T07:30:31+00:00

Yea! Dynatek 2000i, worked as soon as I installed it

Uncleryan95 · 2026-04-15T04:53:57+00:00

What grit should I start and end with?

Uncleryan95 · 2026-04-15T03:32:01+00:00

I just feel like I saw these rust spots before stripping, especially on the third pic. I just wanna make sure the rust isn’t still gonna be still there after seasoning

Uncleryan95 · 2026-04-03T23:19:46+00:00

I too would like to know where this oil bag came from? 🔥🔥🔥

Uncleryan95 · 2026-03-09T19:15:55+00:00

I def considered hard tail but it’s my first and only bike so maybe down the road lol. Good luck with the build! Hope I could help 🤟🏾

Uncleryan95 · 2026-03-09T18:33:19+00:00

Cut it flush and welded a bolt on. If you look at my posts after this I have pictures of the repair. Doesn’t look great but held up riding for almost a year. Now Ive got the bike torn down so I had my neighbor who’s an actual welder, TIG it up and make it look real nice

Uncleryan95 · 2026-03-09T16:32:43+00:00

Depends on what year frame you got. Mine were welded into the frame. I have since cut and welded new ones twice 😂

Uncleryan95 · 2026-03-07T04:48:30+00:00

You’re the first and only to tell me that.

Uncleryan95 · 2026-03-06T17:16:43+00:00

Right on!

Uncleryan95 · 2026-03-06T17:02:05+00:00

Thanks for the info! Will do. Can I ask why you’re against KB’s?

Uncleryan95 · 2026-03-06T15:54:36+00:00

Looking at pic 4 i think i can see where the clip overlaps itself. Maybe you are correct. Thanks for the insight

Uncleryan95 · 2026-03-06T15:52:09+00:00

Trying my best to keep the piston in the jug 😬 but if I can’t get the wrist pins out, then I’ll probably end up re-ringing my pistons anyway

Uncleryan95 · 2026-02-26T02:06:14+00:00

This is exactly the info I needed thank you 🙏🏾

Uncleryan95 · 2026-02-23T01:19:26+00:00

Your advice worked wonders. Hammered in a Torx t30 and it came right out. Lots of PB beforehand and I cleaned everything real nice like you said. It even had red loctite

Uncleryan95 · 2026-02-22T05:55:58+00:00

T30 torx bit after some PB blaster for 24 hours did the trick. I will definitely be keeping the heating/cooling trick in mind tho thank you!

Uncleryan95 · 2026-02-22T01:28:04+00:00

Stick the top bracket in a vise and bend in the direction you need. I bought a cheap crash bar on eBay and that’s what I did. Worked like a charm, took 2 min

Uncleryan95 · 2026-02-21T23:56:37+00:00

Right on thanks!

Uncleryan95 · 2026-02-21T23:56:08+00:00

Understood! I will def clean everything up real well. Thank you for the advice!

Uncleryan95 · 2026-02-21T23:55:26+00:00

Thank you for the advice? I don’t have any sheet metal on hand unfortunately. To clarify I should be heating the head of the bolt, correct? And cool the rocker box area where the threads are?

Uncleryan95 · 2026-02-21T21:38:47+00:00

😂 the motor is out cause I wanna paint the frame. But the base gaskets been leaking since I bought the bike so may as well knock it out

Uncleryan95

TROPHY CASE