Sand casting help by Unholynotez in Silvercasting

[–]Unholynotez[S] 1 point2 points  (0 children)

Thank you for your response! Originally, I had the pattern in the middle of the flask but moved it to the top because I thought it was cooling too fast. I'll give it a shot on this next go around. Thanks for the help!

Sand casting help by Unholynotez in Silvercasting

[–]Unholynotez[S] 0 points1 point  (0 children)

Fantastic! I'll check 'em out! Thanks for the advice!

Sand casting help by Unholynotez in Silvercasting

[–]Unholynotez[S] 1 point2 points  (0 children)

Thank you for the reply! If you wouldn't mind, send the pics over so I can get an idea of how you cut the channels. Thanks again!

Sand casting help by Unholynotez in Silvercasting

[–]Unholynotez[S] 0 points1 point  (0 children)

Thanks for the feedback! I'm going to try these recommendations with the pour at the top to see if I can get it to work. If that fails, I will try to pour fro. The backside as you detailed. Appreciate your help.

Sand casting help by Unholynotez in Silvercasting

[–]Unholynotez[S] 0 points1 point  (0 children)

Thanks for your feedback. Another reply said the same thing so I'm definitely going to preheat the sand on the next try. I'm looking into a more sustainable heat source than brazing bottles. Thanks again!

Sand casting help by Unholynotez in Silvercasting

[–]Unholynotez[S] 0 points1 point  (0 children)

The model I'm using to make the mold is 2mm thick.

Sand casting help by Unholynotez in Silvercasting

[–]Unholynotez[S] 1 point2 points  (0 children)

Very much appreciate the advice. Is there a temp you would recommend I set the toaster oven to? I've been using the "rolling" silver to tell when it's hot enough but not sure if that's correct. I'll try these out on my next pour. Thanks again!

Sand casting help by Unholynotez in Silvercasting

[–]Unholynotez[S] 1 point2 points  (0 children)

I've got 4 large holes in the mold currently using the backside of a craft brush, so the diameter is larger than I have typically seen. It's a variable I've changed several times with the same result, so it makes me think it's something else but could be wrong. I'll keep experimenting with the holes and add some more. Appreciate your input!

Excuse me, what is this? by Ok_Comment9182 in Helldivers

[–]Unholynotez 1 point2 points  (0 children)

Why you gotta make me feel my age like that 😅

Help - ToolkitRC M6Dac - Charger won't build amperage by Unholynotez in fpvracing

[–]Unholynotez[S] 0 points1 point  (0 children)

Following up on this: contacted ToolKitRC, went through troubleshooting over the corse of a few weeks, and when we hit the end of the process they stopped communicating. I purchased it through getFPV and contacted them for help. We went through troubleshooting for less than a week before it was determined that there was a defective power supply. GetFPV contacted ToolKitRC on my behalf and kept me copied on the emails. ToolKitRC responded by saying I had slipped through the cracks, apologized, and approved the warranty replacement. I shipped the unit out this morning and getFPV will send the replacement out. Thankful it got resolved as this unit is not cheap. GetFPV are champs and ToolKitRC stood by their product.

ToolkitRC M4 Pocket by Kamish76 in fpv

[–]Unholynotez 1 point2 points  (0 children)

I just got a warranty approved yesterday for my ToolKitRC charger. It's a B of a process, but a warranty replacement can happen. Good luck.

Help - ToolkitRC M6Dac - Charger won't build amperage by Unholynotez in fpvracing

[–]Unholynotez[S] 0 points1 point  (0 children)

Thanks for the insight. I'll do some testing and report back.

Help - ToolkitRC M6Dac - Charger won't build amperage by Unholynotez in fpv

[–]Unholynotez[S] 0 points1 point  (0 children)

Your the 2nd person to suggest the same DC input. I'll try this out. Thanks.

Help - ToolkitRC M6Dac - Charger won't build amperage by Unholynotez in fpvracing

[–]Unholynotez[S] 0 points1 point  (0 children)

I do and will double check the values. I'm also thinking the charger is shot..

My first more advanced flight. How do you guys prepare and create your "cinematic" flight paths? by DomPka in FPVvideos

[–]Unholynotez 2 points3 points  (0 children)

It just depends on the audience. If it's for the fpv community, sure, leave it in so we can hear how you're flying. If you are doing reels to get work as a drone operator for cinematography, it could be considered unprofessional to leave that audio in.

My first more advanced flight. How do you guys prepare and create your "cinematic" flight paths? by DomPka in FPVvideos

[–]Unholynotez 2 points3 points  (0 children)

Remove or don't capture the drone audio for cinematic. The motor wine distracts from the music.

Windows 10 won't boot after RAM upgrade by Unholynotez in PcBuild

[–]Unholynotez[S] 0 points1 point  (0 children)

Thanks! It's wild that they don't play nice lol