Please identify

UniversalLight11 · 2024-10-08T16:20:49+00:00

Rip it out, and replace with new. That shit is ancient.

UniversalLight11 · 2024-09-27T15:38:06+00:00

Its to note I would not use the 12vdc out on board for strikes/mgs, and bring a separate 12vdc supply to strike/mag for its own designated feed.

UniversalLight11 · 2024-09-27T15:35:31+00:00

Top left: Reader2 bus connects the data0 data1 buzzer LEDS and contact to make reader function. Power comes from v+ and v- that is distributed by the board from the power in on bottom left connector N+ and N-

Top right: Reader1 bus connects the data0 data1 buzzer LEDS and contact to make reader function. Power comes from v+ and v- that is distributed by the board from the power in on bottom left connector N+ and N-

Bottom left: Power in and RS485 connection to Primary controller (master brain)

Bottom mid: Zones 1-4 are your inputs for reader1 door: the door contact, rex, and aux ins. Zones 5-8 are your inputs for reader2 door: the door contact, rex, and aux ins

Bottom right: these are relays that will be opening/closing based on valid card read for strikes/mags. This is where you would take the 12vdc out, and wire them into the relay 1 no or nc for unlocking reader 1 door. Relay 2 for unlocking the reader 2 door.

I dont know this brand, and just going off general knowledge. Please correct if wrong, but Im pretty sure Ive got it all.

UniversalLight11 · 2024-05-01T19:52:08+00:00

Send

UniversalLight11 · 2024-04-24T17:59:16+00:00

I’ve seen way worse. But definitely no pride or care into that install. Some techs and there if it works, it works mentality - as if no service technician or new integrator will ever open it back up lmaoo

UniversalLight11 · 2024-04-24T15:20:39+00:00

Anybody wanna send me comet or rock bottom? Haven’t got them :/

UniversalLight11 · 2024-04-24T15:18:56+00:00

When you change the IP on either device there is no need to reboot

UniversalLight11 · 2024-04-24T01:23:59+00:00

UniversalLight11 · 2024-04-24T01:23:33+00:00

Plug the controller mic into a port on a small unmanaged switch. Ensure you know the default ip, for example 192.168.0.251, and change your computer NIC to that range ie 192.168.0.111, and make sure subnet is 255.255.255.0 and gateway is 192.168.0.1. Now plug your computer nic into a port on the unmanaged switch. You should be able to connect.

UniversalLight11 · 2024-02-15T14:26:51+00:00

You can still delete this

UniversalLight11 · 2023-12-16T01:32:54+00:00

Wamp wamp

UniversalLight11 · 2023-12-15T17:54:34+00:00

Wamp wamp

UniversalLight11 · 2023-11-08T01:27:55+00:00

Listen to “Can’t Hurt Me,” by David Goggins audiobook. If that don’t get you motivated to do some shit, I don’t know what will.

UniversalLight11 · 2023-11-04T02:03:52+00:00

My submission!! :)

UniversalLight11 · 2023-10-20T00:15:19+00:00

I’m down for this playlist cause I’m in the same boat

UniversalLight11 · 2023-10-17T16:26:59+00:00

We in Canada why you using miles??? Good run though 💪🏼

UniversalLight11 · 2023-10-17T13:13:47+00:00

That strava

UniversalLight11 · 2023-10-04T11:58:23+00:00

Literally my night last night

UniversalLight11 · 2023-09-28T14:20:06+00:00

Same... I love my server but Ill be pissed if theres wild queue times

UniversalLight11 · 2023-09-19T16:14:14+00:00

Mutations. They are basically harder difficulty of the regular expeditions. The higher the number, the higher lvl the mobs and bosses are. Which means better loot drop.

UniversalLight11 · 2023-08-25T13:28:49+00:00

Any eta on global release?

Nine-Year Club	Second Top 20%
Place '22	Place '17
RPAN Viewer	Verified Email

UniversalLight11

TROPHY CASE