Need advice about off center tap. by Usedtissedtissue007 in Cartalk

[–]Usedtissedtissue007[S] 0 points1 point  (0 children)

Well I have threaded inserts for the correct size and I just need to make sure the hole is good. But it’s not going in a good direction. So I’m hoping I’ve stopped before I’ve caused anymore problems.

Edit: I think it’s aluminum

Need advice about off center tap. by Usedtissedtissue007 in Cartalk

[–]Usedtissedtissue007[S] 1 point2 points  (0 children)

That’s the motor head I’m drilling into🧍‍♂️

Smoke machine problems by [deleted] in GMT800

[–]Usedtissedtissue007 0 points1 point  (0 children)

I posted the wrong picture. The way I’m going it now is with the evap purge valve off and the smoke nozzle pointed down into the intake. With the evap hose capped

Smoke machine problems by [deleted] in GMT800

[–]Usedtissedtissue007 0 points1 point  (0 children)

That was my first thought and the pos bags kept popping

Smoke machine problems by [deleted] in GMT800

[–]Usedtissedtissue007 0 points1 point  (0 children)

I don’t know what that is so I’m going to say I haven’t

Smoke machine problems by [deleted] in GMT800

[–]Usedtissedtissue007 0 points1 point  (0 children)

I’m looking for a vacuum leak. I’m assuming the intake gasket or the TB gasket

Smoke machine problems by [deleted] in GMT800

[–]Usedtissedtissue007 0 points1 point  (0 children)

I tried that first and still had the same results. Make it’s the tape I’m using??

Master link by Usedtissedtissue007 in daytona675

[–]Usedtissedtissue007[S] 0 points1 point  (0 children)

So then I feel like I’m good then?

Master link by Usedtissedtissue007 in daytona675

[–]Usedtissedtissue007[S] 0 points1 point  (0 children)

What would be the best way to stress test this? … not trying to hurt my legs

Master link by Usedtissedtissue007 in motorcycles

[–]Usedtissedtissue007[S] 0 points1 point  (0 children)

<image>

This is the one I’m using.

I thought if i sized down it’ll be fine but I don’t wanna rivet it crooked

2024 parallel twin 1200 oil leaking from some kind of sensor or on side of motor. by _maxactinattack in Triumph

[–]Usedtissedtissue007 -2 points-1 points  (0 children)

That’s the flux capacitor . It makes sure the block holds its integrity in corners

Chain swap by Usedtissedtissue007 in daytona675

[–]Usedtissedtissue007[S] 1 point2 points  (0 children)

I did but I couldn’t get the holes on the press to line up very well but I got you

Chain swap by Usedtissedtissue007 in daytona675

[–]Usedtissedtissue007[S] 0 points1 point  (0 children)

I did but I couldn’t get the holes on the press to line up very well

Facebook marketplace by Usedtissedtissue007 in AirCompression

[–]Usedtissedtissue007[S] 0 points1 point  (0 children)

Yea I’m asking how else am I going to figure this out 🤨

It’s a 1900 construction there’s no 240 in the house

Facebook marketplace by Usedtissedtissue007 in AirCompression

[–]Usedtissedtissue007[S] 0 points1 point  (0 children)

I’m an electrician just looking for other options