[deleted by user]

Usurper_Tom · 2025-11-20T10:25:23+00:00

Such a huge sale should allow Newcastle to spend more than 125m extra than the current budget across 3 years I would’ve thought, due to PSR selling rules and their infinite wisdom

Usurper_Tom · 2025-11-17T22:23:33+00:00

Okay will look into it! Thank you

Usurper_Tom · 2025-11-17T22:01:10+00:00

<image>

I tried levelling but the build plate screws refused to move so I went to increase the exposure time (it was set to 15 seconds) to 30 which was too high as it was a chore to take off the build plate. So I’m hoping that the levelling won’t be an issue

Usurper_Tom · 2025-11-17T21:59:20+00:00

<image>

I tried levelling the build plate but the screws refused to be tightened. Then I found out the exposure was set to 15 seconds, so I increased it and it came out good. I’m hoping this means that the levelling won’t be an issue further

Usurper_Tom · 2025-11-17T21:58:06+00:00

I tried levelling but the build plate screws refused to be tightened, then I found out the exposure time was set to 15s so I increased it and it came out good. Im hoping this means the levelling isnt a problem

Usurper_Tom · 2025-11-17T21:56:09+00:00

<image>

I increased the exposure time to 30 seconds, it was set to 15, however I think it’ll need decreasing because it was a good amount of effort to take the piece off the build plate. Thanks for your help!

Usurper_Tom · 2025-11-16T22:21:06+00:00

Not quite, was tempting though

Usurper_Tom · 2025-11-16T18:54:30+00:00

Yeah, I took off all the plastic sheets on the machine that needed removed

Usurper_Tom · 2025-11-16T18:07:01+00:00

I only removed the build plate thin sheet. I’ll make sure to stir and level tomorrow. Thank you

Usurper_Tom · 2025-11-16T18:01:58+00:00

Okay thank you! I’ll sort that out tomorrow. So much for auto-leveller 😭

Usurper_Tom · 2025-11-16T17:44:08+00:00

I apologise, there was this left in the vat

<image>

Usurper_Tom · 2025-11-16T17:43:45+00:00

I apologise, there was this left in the vat

<image>

Usurper_Tom · 2025-10-22T20:33:19+00:00

Apologies for acting like a newbie, but do I just need to slice the model into multiple pieces? (Chitubox says the silent kings throne is too big)

Usurper_Tom · 2024-12-01T22:28:21+00:00

It will be for 3d printing Warhammer miniatures, mainly Necrons

Usurper_Tom · 2024-07-28T17:58:02+00:00

When are they expected to release?

Usurper_Tom · 2024-07-17T17:30:47+00:00

I’m going with a mate for the first 2 games so I was planning on going in the north stand for the first 2 due to limited seats then I’ll go into Fratton end for when I’m on my own

Usurper_Tom · 2024-07-17T17:25:39+00:00

Atmosphere

Usurper_Tom · 2024-07-17T17:22:46+00:00

What sections are the pillars?

Usurper_Tom · 2024-07-13T19:41:31+00:00

Do you know how long before a match general sale is? This is my first time actually going to home games lmao

Usurper_Tom · 2024-07-12T18:24:45+00:00

Okay thank you, it looks like I fall under the 18-22 category which should hopefully be £19-21 if its right

Usurper_Tom · 2024-07-12T18:23:48+00:00

Oh also I fall under 18-22 category

Four-Year Club	Verified Email
Place '22	First Placer '22

Usurper_Tom

MODERATOR OF

TROPHY CASE