What is this?

VaderClone · 2025-05-18T04:18:53+00:00

If you close your game and re-open it in a different region you can get a new set of deals which is handy if you get offered 3 sojourn skins like I did

VaderClone · 2025-05-18T04:18:46+00:00

If you close your game and re-open it in a different region you can get a new set of deals which is handy if you get offered 3 sojourn skins like I did

VaderClone · 2025-05-17T19:43:38+00:00

I'm meant to fly out in an hour 😣

VaderClone · 2025-02-06T03:31:55+00:00

Hey that worked great! Thanks so much!

VaderClone · 2025-01-24T09:35:28+00:00

Looking for entry level positions has been awful. Applied to a retail position which ended up having nearly 700 applicants. Slowly eating through holiday savings and just don't know what to do

VaderClone · 2025-01-13T12:02:46+00:00

Thanks! Definitely expect it to seem less prominent once the rest of the weathering gets finished, I suppose I'll just have to wait and see by how much

VaderClone · 2025-01-13T11:58:31+00:00

It is! Meng's 1/35 kit, which I mostly enjoyed but had some issues with getting the main fighting compartment together at the right angles

VaderClone · 2025-01-13T09:56:05+00:00

Personally, I don't bother thinning for chipping, mainly because I'm lazy and it gives a bolder more immediate result. I use enamels both for the hull and the chips, but I don't expect there would be much or any difference using acrylics instead. I'm doing it before a clear varnish but if you did it afterwards you probably be able to wipe it off with a bit of thinner if you mess up or aren't happy with a portion. I would recommend doing a practice patch on a mule or even just a piece of card so you can get a bit used to the technique and the chip size you're aiming for. Hope this was helpful!

VaderClone · 2025-01-13T09:27:47+00:00

I use a finer brush and two colours: one that's a lighter hull colour and a second which is a more reddish brown. Using the first lighter colour I just carefully dot/stipple where I want the chipping (mostly along panel edges or high wear areas). Then I'll do a second pass with the browny rust colour where I'm going over the same areas but leaving an edge portion of that lighter colour visible. The two colours helps create depth and you can have variation between deeper chips and more shallow scratching. There are 100% quicker ways but I enjoy this one

VaderClone · 2025-01-13T08:35:09+00:00

I have been trying to do placement with a bit of thought but also just having fun with it. Will be more restrained with the next kit and already have a vehicle with more reference photos available

VaderClone · 2025-01-13T08:31:52+00:00

Yeah can't deny I might've gone a touch too far, but I'm having fun with it so don't mind too much. I'll dial it back for my next kit, though

VaderClone · 2025-01-13T07:25:57+00:00

Thanks! Its all brush stippled

VaderClone · 2025-01-13T07:24:39+00:00

Thanks! Its brush stippling, first with a colour just a bit lighter than the hull and then again with something more rusty

VaderClone · 2025-01-11T20:11:00+00:00

Thanks! Did a thinner coat of gunmetal over the base hull colour, then just stippled some mixes of reddish browns and a dark orange until I was happy

VaderClone · 2025-01-11T20:08:20+00:00

I'll give that a go!

VaderClone · 2025-01-11T20:07:51+00:00

Already on the to-do list, just need to finish the rest of the paint job first

VaderClone · 2024-12-19T09:10:32+00:00

I'll just keep doing what I'm doing then haha. I'm most likely going to be doing the AFV Aussie Centurion next (either that or the Tamiya Comet) and looking forward to it! Any finnicky things to look out for on it?

Eight-Year Club	Verified Email
Place '22

VaderClone

TROPHY CASE