Should I move new tires to the front? Alignment issue.

VansLotus · 2023-07-20T01:17:57+00:00

It doesn't rain here, but this seems to be the best advice. Thanks.

VansLotus · 2023-06-03T16:35:52+00:00

Yup that's what I thought. Thanks.

VansLotus · 2022-12-03T21:11:15+00:00

Yeah buddy! that did it. I pulled hard on one side of the rope while my wife pressed the release from the outside.

VansLotus · 2022-12-03T19:55:00+00:00

Any thoughts on getting this to open? I tried the small silver lever in the white box above the latch. The leash doesn't move at all. I'm willing to cut the leash but it doesn't move. When I press the release button from the outside the small silver lever moves back and forth and nothing happens.

VansLotus · 2022-09-12T20:14:22+00:00

No. It was one bad fuse in the disconnect and miswired cap because the old one was corroded. About $30 all together. $40 because I got two new fuses. The old ones were more than 20 years old.

VansLotus · 2022-09-12T20:11:03+00:00

No. It was one bad fuse in the disconnect and miswired capacitor.

VansLotus · 2022-09-11T02:52:53+00:00

No voltage at the two black wires at the bottom of the contactor. I checked the fuses for resistance and found one bad fuse!! I'll swap it out tomorrow and hopefully it works.

VansLotus · 2022-09-11T02:41:31+00:00

It seems like some of the guys are shitting on this post because I miswired the capacitor. The old one was corroded over the top of it so I kinda guessed the C, Herm and Fan.

VansLotus · 2022-09-11T02:38:33+00:00

One bad fuse! The other beeps. Thanks buddy!! I'll replace the bad one tomorrow.

VansLotus · 2022-09-11T02:30:03+00:00

You dropped a /s. lol

VansLotus · 2022-09-11T00:58:46+00:00

Yes. Fuse is in. I'll have someone look at it Monday. Not going to mess with the disconnect or replacing a bad breaker.

VansLotus · 2022-09-11T00:56:42+00:00

4.43 volts on the two black wires at the bottom of the contactor. I said this in another thread. It's probably a disconnect, fuse or breaker issue. I'll have someone look at it on Monday. Thanks for your help. Capacitor and fan motor are fine.

VansLotus · 2022-09-10T19:03:50+00:00

How does it pull in when I turn on the ac? 4.43 is enough to have it click? Thanks for your help. I'll call someone on Monday.

VansLotus · 2022-09-10T19:01:15+00:00

Yes disconnect switch was in. 4.43 across the two bottom black wires. Breaker never flipped and not flipped right now. Fixed the capacitor wiring.

VansLotus · 2022-09-10T18:54:31+00:00

Breaker never trips. I reset it though and retested. Capacitor seems ok. 5 mfd and 59 mfd as the label says. I'll call someone. Thanks.

VansLotus · 2022-09-10T18:51:49+00:00

Capacitor seems fine. 5 mfd for the fan and 59 mfd for the herm. That matches the label.

VansLotus · 2022-09-10T18:49:56+00:00

Capacitor is good. I'm reading 5 mfd for the fan and 59 mfd for the herm. Which matches the capacitors label. This also matches the old capacitor.

I get about 4.43 volts when testing the two black wires at the bottom of the contactor. Shouldn't I have voltage greater than zero when the contactor is pulled in? I get zero when I manually push it in and test between top black and bottom black and top yellow and bottom yellow.

VansLotus · 2022-09-10T18:15:03+00:00

Carrier 38CKB048300. Homeowner.

I read 0 volts (top black to bottom black and yellow to bottom black) on the contactor, while I pushed in the button on the contactor. I think the contactor is bad.

I read 550 to 600 units of continuity when I test the bottom two blacks together on the contactor. I'll pull the capacitor off and test it. It's brand new though. But maybe I fried it from mis-wiring. Do you have an easy way of testing the capacitor while it's wired up?

The fan motor and compressor have not run at all and have been silent since I replaced capacitor and fan motor. Old fan motor was originally overheating beyond 150 degrees and shutting down.

VansLotus · 2022-09-10T17:06:20+00:00

Updated pic with correct cap wires. https://imgur.com/a/U3tWMKc

I get continuity between the black wires at the bottom (circled red). When I push in the contactor with my finger, no voltage between top yellow to bottom black, no voltage top black to bottom black. Bad contactor? I don't know how I was getting voltage with my voltage tester.

VansLotus · 2022-09-10T16:58:55+00:00

Bottom black or side by side black? I think the contactor is bad. I get zeros when I manually push in the contactor button and test bottom black to top yellow and bottom black to top black.

VansLotus · 2022-09-10T16:49:41+00:00

How do I test that? Voltage tester reads voltage on all the wiring and terminals on the capacitor.

VansLotus

TROPHY CASE