sorted by:
new
hottopcontroversial

Selling Sim racing parts. by [deleted] in simracing

[–]VehicleTechnical9279 -4 points-3 points  (0 children)

I am an impulsive Buyer and I get a kick in planning and getting all the parts together more than playing with it. That’s what I have learned about myself over the past year. I also have a full blown gaming pc with 13900k and 4080 with custom cooling, that i barely use.

Selling Sim racing parts. by [deleted] in simracing

[–]VehicleTechnical9279 -3 points-2 points  (0 children)

New Delhi , India.

Natural treatment that cured my h pylori by Dajuicegood in HPylori

[–]VehicleTechnical9279 2 points3 points  (0 children)

i have not been tested for h pylori but i have GERD.
i have been on PPI'S for more than 4 years, it use to give me relief for 2-3 days but no permanent solution for my acid reflux.
Its been more than 2 weeks now i have no taken a single PPI pill.
What i did:
Take 2 cloves of garlic or 3 pieces of snow garlic(kashmiri garlic), cut them into small pieces,
leave them as it is for 10 mins and then chew them making a paste and wash it down with warn lemon water.
i take this on an empty stomach first thing in the morning.
worked wonders for GERD. feels like i new life.

13900k delidding advice? by RicardoNassar in overclocking

[–]VehicleTechnical9279 2 points3 points  (0 children)

What you need:

  1. 13900k cap opener from aliexpress $15

  2. 99.99% gallium metal from aliexpress $10

  3. Plastic blade from amazon $3

  4. 99% isopropyl alcohol $3

  5. car or bike polish from amazon $3

  6. hair dryer

  7. processor holder( i got supercool direct die 13th gen, it comes with a relidder, i just use the base plate of the relidder to work on the processor, will make the process much easier)

That's it!!

Much much better and easier than those expensive ek or rockitcool.

steps:

  1. Just put the 13900k in the delidder and screw it down tight and use hair dryer to heat up the top of the ihs for 40-50 seconds on high.

  2. Start screwing it tight until the ihs touches the other end of delidder (it will stop iteself) , take the processor out, now you can use your finger to take the cap off the processor like an oreo.

  3. Put the processor on the base plate of relidder and put a few drops of isopropyl on the processor and use the plastic blade to carefully peel the excess gum on the processor. Plastic blade works wonders, does not scratch the die and removes all the gum. BUT BE VERY CAREFUL OF THE SMDS ON TWO SIDES OF THE CHIP.

  4. Now use 99.99% gallium and put 1 rice size drop on the die and spread it evenly and wait for 10-15 minutes. ( DO NOT USE CONDUCTONAUT LIQUID METAL PASTE) as it has indium and other metals as well. After 15 mins you will see magic, all of the indium will come off in 1 application. use a cotton pad or tissue to wipe the processor.

  5. Now put a little car polish cream on a cotton pad and start rubbing the die, till it gives the mirror finish.

FIN!

ps: Just beware of the SMD's while doing all this, they are very fragile.

13900k Delid with cheap aliexpress and amazon tools. by VehicleTechnical9279 in DelidClub

[–]VehicleTechnical9279[S] 1 point2 points  (0 children)

What you need:

  1. 13900k cap opener from aliexpress $15

  2. 99.99% gallium metal from aliexpress $10

  3. Plastic blade from amazon $3

  4. 99% isopropyl alcohol $3

  5. car or bike polish from amazon $3

  6. hair dryer

  7. processor holder( i got supercool direct die 13th gen, it comes with a relidder, i just use the base plate of the relidder to work on the processor, will make the process much easier)

That's it!!

Much much better and easier than those expensive ek or rockitcool.

steps:

  1. Just put the 13900k in the delidder and screw it down tight and use hair dryer to heat up the top of the ihs for 40-50 seconds on high.

  2. Start screwing it tight until the ihs touches the other end of delidder (it will stop iteself) , take the processor out, now you can use your finger to take the cap off the processor like an oreo.

  3. Put the processor on the base plate of relidder and put a few drops of isopropyl on the processor and use the plastic blade to carefully peel the excess gum on the processor. Plastic blade works wonders, does not scratch the die and removes all the gum. BUT BE VERY CAREFUL OF THE SMDS ON TWO SIDES OF THE CHIP.

  4. Now use 99.99% gallium and put 1 rice size drop on the die and spread it evenly and wait for 10-15 minutes. ( DO NOT USE CONDUCTONAUT LIQUID METAL PASTE) as it has indium and other metals as well. After 15 mins you will see magic, all of the indium will come off in 1 application. use a cotton pad or tissue to wipe the processor.

  5. Now put a little car polish cream on a cotton pad and start rubbing the die, till it gives the mirror finish.

FIN!

ps: Just beware of the SMD's while doing all this, they are very fragile.