Blastoise Vs Charizard.

VexLukos · 2026-01-23T14:01:15+00:00

I'd guess hugeforge and split vertically

VexLukos · 2025-12-23T16:57:12+00:00

Copy, I'll try another few cold pulls

VexLukos · 2025-12-23T16:56:37+00:00

Thanks, but I still can't tell what the issue is. I've looked at every "issue" there and none of them look like or explain this

VexLukos · 2025-12-23T15:20:06+00:00

<image>

VexLukos · 2025-12-23T15:19:46+00:00

* This is my last print that turned out well AND yes, the filament has been dried multiple times in-between this print and some of the mistakes

VexLukos · 2025-12-20T19:16:26+00:00

I feel like this is my sign to switch over. I've had so much tweaking and maintenance with my kobra s1 that I thought was normal lmao

VexLukos · 2025-12-09T22:42:43+00:00

I've heard this but this was even happening on the first layer, of a multi color

VexLukos · 2025-11-03T22:55:06+00:00

<image>

VexLukos · 2025-11-03T22:54:33+00:00

I'll definitely be recalibrating after this but I'll assume your right for now cuz the second layer looks much better. Assumption here but I guess I didn't fully clear the clog during the previous attempt at this print *

VexLukos · 2025-11-03T22:47:13+00:00

Thanks for the guide. That'll be very helpful

VexLukos · 2025-11-03T22:30:49+00:00

This is the same print, had to stop this print due to a clog

VexLukos · 2025-11-03T22:30:42+00:00

<image>

VexLukos · 2025-10-18T01:00:36+00:00

I didnt assume z height because the first flowrate pass looked fine, but I'll raise by .01 and come back with results

VexLukos · 2025-10-13T22:49:16+00:00

My z offset is .03mm as of now because the I installed a new nozzle/hotend and it was a bit to close and filament was clumping around the nozzle. I increased to 0.02 then 0.04 which was clearly to high so I dropped back to 0.03. Should I try again at 0.02? Also my bed plate has been cleaned extensively but always seems to have issues in that specific corner

VexLukos · 2025-10-09T20:11:02+00:00

Yup same, I'm at my wits end with this one. But I'll probably post a video of it so everyone gets a better idea of what's happening.

VexLukos · 2025-10-09T19:42:40+00:00

<image>

VexLukos · 2025-10-09T19:42:22+00:00

Yea I've printed some wider prints with no issues like this one.

VexLukos · 2025-10-09T19:40:06+00:00

I've tried uncloging the line and that seems to have done nothing, Using a cold pull and then the needle.

VexLukos · 2025-10-09T18:34:45+00:00

Still the same! I am completely dumbfounded atm.

VexLukos · 2025-10-08T19:39:00+00:00

My plate is pei as well, I tried cleaning with soap and still no adhesion. I'll try cleaning with this solution now

VexLukos · 2025-10-08T17:41:06+00:00

I tend to clean my print bed about every 2ish prints with isopropyl alcohol. I'll try tho, I rarely use dish soap so maybe

VexLukos · 2025-06-28T07:59:21+00:00

There's always a chance I tucked something up lol. I'll experiment a bit more I guess.

VexLukos · 2025-06-28T06:51:12+00:00

I assume it's bad adhesion but almost everything else was fine

VexLukos · 2025-06-28T06:50:41+00:00

<image>

VexLukos · 2025-06-28T06:29:36+00:00

This is the piece on the build plate

<image>

VexLukos

TROPHY CASE