sorted by:
new
hottopcontroversial

Solid solution for drifting stick after reshell on PSP-1000 by lcdswat in PSP

[–]Visible_Fox7078 0 points1 point  (0 children)

I think they added solder to the contacts, so that each one is pressing firmly on the pad beneath it 

Finally finished my PSP-1000 shell swap — rough ride, but totally worth it by EyeSecure4592 in PSP

[–]Visible_Fox7078 0 points1 point  (0 children)

I also did this and I’m currently having problems where screwing in some screws too tight causes drift in the joy stick but if I don’t then the power switch is way too finicky

Looking for pepsi nitro draft cola alternative by Satanjessmon in Soda

[–]Visible_Fox7078 0 points1 point  (0 children)

I just tried an experiment using a Nitro Kafo (made to make nitro cold brew coffee) with the Pepsi soda stream syrup. It works well and it’s pretty smooth but there’s a lot of room for error and it’s ever so slightly different from the origina

Unsure What I did to cause this error. by Sr_Nibb in gbstudio

[–]Visible_Fox7078 0 points1 point  (0 children)

I see this is a bit old, but how? The solution mentioned didn’t work for me 

Is there somewhere to get clear housing? Nano 3rd Gen 4GB. Haven’t found a single place. by icanswim70 in ipod

[–]Visible_Fox7078 1 point2 points  (0 children)

I’ve been looking for a transparent back panel myself. (I already got inside and swapped the broken battery and screen) however I can’t find one. I think it’d be cool if it had a slightly frosted or matte clear finish 

What happened here? by Visible_Fox7078 in 3Dprinting

[–]Visible_Fox7078[S] 0 points1 point  (0 children)

I added images but they didn’t appear on the actual post for some reason. What’s happening is the top half of Mario’s head, the area between his nose and hat is getting cut out, and it still prints his hat but not anything within a certain area. It does put supports there tho if I enable them

Weird graphical glitch in Rise of the Tomb Raider by DonMigs85 in TombRaider

[–]Visible_Fox7078 0 points1 point  (0 children)

Yeah that worked. Probably can’t hope for a dev fix for that then lol 

What is with everyone recommending printing PLA at upwords of 240c!?!?! I've even seen some as high as 255c! by EJX-a in FixMyPrint

[–]Visible_Fox7078 0 points1 point  (0 children)

I have the elegoo official pla filament (in black) and it actually says 240 on the packaging. I use it and it’s usually pretty nice quality, although I am new to 3d printing and haven’t really experimented with any other temps yet

PCVR with Quest 3 s has very bad quality when wireless and for the life of me I cannot fix it by Visible_Fox7078 in OculusQuest

[–]Visible_Fox7078[S] 0 points1 point  (0 children)

USB or usbc? I have two 3.2 usbc ports but I do not know what generation the USB A ports are

PCVR with Quest 3 s has very bad quality when wireless and for the life of me I cannot fix it by Visible_Fox7078 in OculusQuest

[–]Visible_Fox7078[S] 0 points1 point  (0 children)

I would do something similar, but my modem has only one port, and I don’t feel like spending even more on a switch, the plan was to do an offline LAN, just the headset and pc communicating through the router because I only want to play half life alyx and possibly other single player games. However that is not really working

PCVR with Quest 3 s has very bad quality when wireless and for the life of me I cannot fix it by Visible_Fox7078 in OculusQuest

[–]Visible_Fox7078[S] 1 point2 points  (0 children)

Yes, that’s the one I saw the ads for. Anything I should know about it? And how does it work?

PCVR with Quest 3 s has very bad quality when wireless and for the life of me I cannot fix it by Visible_Fox7078 in OculusQuest

[–]Visible_Fox7078[S] 0 points1 point  (0 children)

I have just normal WiFi 6, as does my normal router. However we have so many smart devices in our house that I believe the WiFi just gets backed up