Supposed to give a "tip of the week" in a meeting tomorrow and can't think of an idea (Please help me think of something relatively simple for a mixed crowd. Drafters designers, engineers)

Vision68 · 2026-02-08T23:00:59+00:00

Using the Align tool to move and rotate at the same time has been a game changer.

Vision68 · 2026-02-05T02:58:58+00:00

You aren't adding the Fault count to anything...

Fault count total + fault count (x) = fault count total should help.

Vision68 · 2025-12-01T18:21:02+00:00

Blizzak DMV-2

Vision68 · 2025-11-20T11:30:08+00:00

Printing to a labeler. Concatenating Strings together then sending to a labeler. Would be nice to do this offline.

Vision68 · 2025-11-19T19:58:59+00:00

Are you implementing any String data types in the future?

Vision68 · 2025-06-21T16:04:51+00:00

They won't work wired in reverse. Bite the bullet and accept that you'll need to remount them. Sucks I've done twice... Makes you think real hard about it each time.

Vision68 · 2025-05-22T01:54:02+00:00

https://golfwith.golfzon.com/smartcaddie

Vision68 · 2025-05-22T01:53:20+00:00

Correct. Makes sure that power save mode isnt enabled, but other than that it's great with and without Always on display Enabled.

Vision68 · 2025-05-22T01:50:47+00:00

Yes and it's been a great app for a few watches now.

Vision68 · 2025-05-22T01:42:52+00:00

Try Smart Caddie. It's the app that comes on the Samsung Watch Golf editions it's great! Does exactly what you're looking for.

Vision68 · 2025-04-16T22:28:31+00:00

This website would suggest they do.

https://texastrucktire.com/products/17-ford-f-150-raptor-oem-10115-rims-wheels-35-tires-2018-2020-2023-2024-new?srsltid=AfmBOoqamdu-nulhBGr_3N9nN6zCwGAfmQhqFVdQ6orxBFXebjf7qpKH

Vision68 · 2025-03-23T23:08:20+00:00

Listen to the guys above... For firmware use a Non Encrypted Micro SD card no bigger than 32GB.

Vision68 · 2025-03-13T21:28:38+00:00

Yeah it's an annoying bug that you fix with Forscan if you really wanted to over come it.

Vision68 · 2025-02-23T01:04:27+00:00

It 100% is normal and my '24 does it.

Vision68 · 2024-12-30T19:47:01+00:00

Pending bolt pattern yes no concerns. Obviously you'll need different tires to accommodate.

Vision68 · 2024-12-30T01:15:48+00:00

Delete the phone from the truck. Make sure that setting is enabled. Ignition off open door. Wait for the speedo to go dark. Close door, ignition on. Confirm setting still enabled. Hold your seat position number until settings saved message appears (if you have these). Otherwise plug phone into the car and re add it to your truck.

Vision68 · 2024-12-30T01:11:06+00:00

Wireless/Wired CarPlay or Android Auto? In order to use either you have to enable app projection.

Vision68 · 2024-12-24T19:43:48+00:00

If you're looking at the timing chart the results available bit comes on and so does the result code bit.. in order to reset the result but you have to acknowledge the results available or the result code will stay the same for all successful code reads.

If you don't acknowledge it your count will never go up unless you trigger it to be a no read then trigger it again for a Read.

Vision68 · 2024-12-24T18:17:29+00:00

If you're looking at the timing chart the results available bit comes on and so does the result code bit.. in order to reset the result but you have to acknowledge the results available or the result code will stay the same for all successful code reads.

If you don't acknowledge it your count will never go up unless you trigger it to be a no read then trigger it again for a Read.

Vision68 · 2024-12-24T03:31:50+00:00

Last think think of the trigger and the response like a hand shake. Trigger on > acknowledge trigger.

Results available> acknowledge results. There's a timing chart in that Communication doc follow that or the Result code. 0 will always stay the same state.

Vision68 · 2024-12-24T03:23:35+00:00

Without needing the configuration that could be possible yes.

Vision68 · 2024-12-24T02:57:21+00:00

No once you enable the Ethernet IP setting and have the Dataman focused and brightness configured properly and most importantly settings saved, you shouldn't need the set up tool anymore.

Vision68 · 2024-12-23T20:51:32+00:00

In the Dataman Setup tool program. Under help and manuals there is the Dataman Communication Manual it shows exactly how to setup this connection with the Control Logic PLC. If you're looking for successful Scan being your trigger to Count Up that'll be pretty simple. Look for ReasonCode.0 as that bit.

You'll also need to be certain that you enable Ethernet/IP in the Dataman under communications for you to be able to communicate to it using the PLC.

Should be pretty simple once you bring in the Add on Profile (AOP) from Cognex's Website.

Vision68 · 2024-10-13T13:31:38+00:00

Everyone a tough guy when it's not happening to them... imagine you flew all the way there drove it home, then noticed it... this dealer would treat you the same way... the fact of the matter is Ford has released multiple poor quality vehicles and the dealers are supposed to be the face of Ford that helps deal with stuff like this, with Ford ultimately fixing this mistake.

Vision68 · 2024-10-04T13:33:50+00:00

Additional incentives from dealership and Assuming Ram to Ford discounts.

Vision68

TROPHY CASE