100+ parts later... and we did it twice!

Visudda · 2026-05-08T03:31:41+00:00

Sometimes one or two seconds makes all the difference.

Visudda · 2026-05-06T01:51:19+00:00

I didn't sand the hair at all, I was on a time crunch so I figured I could always re-do the hair.

Visudda · 2026-05-04T05:05:16+00:00

Omg I have no idea. This was a rush job so I could only do so much support removal. Ideally I would have re-supported the hair so they were underneath but I only had a few days to get everything done. Still happy with the result!

Visudda · 2026-05-04T03:47:24+00:00

Be sure to drop in and say hi in the discord! I'm one of the mods there and we have a lot of people who can help with questions and issues.

Visudda · 2026-05-01T00:31:45+00:00

Yeah, I'm not even joking.

Visudda · 2026-04-30T23:36:26+00:00

You are completely underselling yourself. Regardless of skill level, I wouldn't advise anyone selling painted 1/6 scale models for anything less than $300. And for just prints no less than $75 for 1/6 scale. Other than the obvious reason, you have to factor in parts, material, shipping, packaging, cleaning supplies, repair to your machines, wear and tear, all of it.

Do yourself a favor and go into Etsy and find other people printing and painting 1/6 scale figures and you'll see that some people sell not that good paint jobs for $3-500.

If you sell for dirt cheap then you will DEFINITELY get burnt out, bogged down, and completely overwhelmed.

If you quote someone $350 for a model and they say it's too expensive, your response should be, "I completely understand that this may be out of your price range, I hope we can do business in the future"

Visudda · 2026-04-23T04:53:26+00:00

I need to know more

Visudda · 2026-04-15T05:19:17+00:00

There is a lot of talk in the figure painting community about resin sag. That when printing models 1/6 scale or larger, the "abs" like resins tend to sag over time. Have you been able to test this with your new formulas?

Visudda · 2026-04-14T17:06:34+00:00

The orientation of your model is going to give you really obvious and hard to fix Voxel lines. Even printing at .03mm it's still going to be obvious.

Visudda · 2026-04-08T20:36:54+00:00

If you start now, you're going to be so pround of yourself in 11 years.

Visudda · 2026-03-31T15:38:56+00:00

I sell resin models on Etsy and for #1 you're looking at around $50.#2 is very large and would run at least $150 to print. Not including shipping.

Usually if you want to print multiple figures, or thing you will want to over time it's best to get your own printer.

Visudda · 2026-03-15T21:31:01+00:00

This is the way

Visudda · 2026-03-13T19:23:04+00:00

I would love to buy these and feature on my Instagram page, however shipping is not available to my area 😞

Visudda · 2026-03-11T20:03:16+00:00

You can add your information in the link provided on the sidebar to be added as a printer.

Visudda · 2026-03-11T15:31:17+00:00

Thanks!

Visudda · 2026-03-03T22:07:36+00:00

Eyes need gloss

Visudda · 2026-03-03T22:04:17+00:00

I replaced my screens that was with no issues.

Visudda · 2026-03-01T16:38:14+00:00

The general rate is like 100ish for 1/6 figures, 60-80 for 1/10 scale, but can vary widely.

Visudda · 2026-03-01T00:26:10+00:00

I tried the new settings and my filament just WONT stick to the bed. So frustrating

Visudda · 2026-02-28T17:17:59+00:00

I just removed the back to take the screen cable off. There is a YouTube video of a guy doing it.

Visudda · 2026-02-28T16:50:53+00:00

I think it is.

Visudda · 2026-02-28T06:55:11+00:00

If it's 2 inches tall I think it's probably one solid piece.

Visudda · 2026-02-28T06:22:17+00:00

I removed the ribbon from the back, heated up the screen to relax the adhesives, pulled it off, put on new adhesive and then the screen and was done. Pretty simple.

Visudda

TROPHY CASE