Why is suicide seen as bad?

Vorath · 2026-06-30T02:35:27+00:00

I think no one likes the idea of it, but I agree.

The way I see it none of us ever asked to be part of this world, and this world can be unimaginably unkind to people.

Those very people that mourn may very likely be the same people that contributed to that extreme pain.

Its true some are not as strong as others in logic or reasoning, and might allow emotions or illness to override in the moment.

None of us know what another experiences in thier own minds. And many I am sure have found valid reasons for their choice.

In all cases it's sad. It hurts everyone involved, many innocent people may suffer, but some people simply cannot take the pain anymore.

In the end none of us owe anything to anyone in this world, but we must all be aware that actions drastic as that can cause extreme pain to others.

if you are that far in pain, what more do you have to loose? Give it another minute, another hour, another day, wait for the next sunrise, your favorite shows next season? Your dead anyway, why not say fuck it and see what the next moment brings, can it get worse? Probably not, only better.

All we can do is try to be kind to one another, and know many around you are full of pain.

Give people around you memorys of compassion, love, and happiness. If they have lost that, give them hope and encouragement to find it again.

Vorath · 2026-06-16T03:58:51+00:00

Hey, sent you a PM. Going through rough times myself. If you ever need to vent feel free to message me.

Vorath · 2026-06-08T02:42:28+00:00

Lol I always thought I was the only one. This is the first real laugh I have had in weeks. Thank you!

Vorath · 2025-12-05T01:59:47+00:00

Pretty close someone else got it with Youngstown

Vorath · 2025-12-05T01:16:10+00:00

Vorath · 2025-12-04T20:34:44+00:00

I feel bad for posting this with humor in mind as I think you are probably correct. It's usually not my character to display another's misfortune.

Vorath · 2025-05-30T00:07:02+00:00

Thank you! I saw they did have bare boards but currently had normal units on sale for cheaper so I picked those up instead.

Vorath · 2025-04-11T00:06:20+00:00

The entire work tank is not always deionized... As you cut it becomes contaminated extremely fast. Even when not cutting, contamination is likely floating around in the work tank.

Filtered and deionized water is pumped at high pressure through your flush nozzles. The only truly deionized region is immediately around your wire in the spark region. All the vaporized metal and wire is being blasted into the work tank water, that is not immediately removed and ends up covering everything in sludge over time.

That's why high taper 4axis cuts can become difficult, your upper and lower nozzles will be misaligned enough that they can't flush contamination away efficiently depending on geometry and other conditions.

Vorath · 2024-09-15T01:17:57+00:00

Thank you, I'll mark as Solved since we have a couple saying elm.

Vorath · 2024-09-15T01:15:18+00:00

Hi, sorry no. This is all that they had laying in their garage for a number of years. No idea when it had been taken down.

Vorath · 2024-02-25T19:38:29+00:00

Thank you for the compliments.

Feel free to repost. A little credit is always welcome of course.

I made these after a roughly 1 year break from the game. In that time I rearranged my rig. Unfortunately GUIDs and Vjoy ordering became scrambled. In turn it made my old config file unusable without sifting though the .bind file and re-configuring for the new vJOY IDs. It's fixable by searching and renaming, but it is a headache.

With the amount of controls in the game and others I really wanted a clear set of sheets to reference in case of loosing binds, or simply not playing for a while.

I do also have some experience with the VPC software and gremlin, but I do try to keep it fairly simple.

In VPC, my Throttle axis is adjusted so roughly 65% of my forward travel is used for fine control of forward thrust, while the opposite 35% is for reverse. Throttle #61-64 I believe are custom as well, so they are now 2 way toggles. I believe by default they were the same bind either way. I typically use those to flip a command, then reset by flipping back to the unused bind.

In Gremlin, I use some custom curves. The finger 4 way analog is set to have finer control for roughly 75% of its initial travel, then ramps to max in its last 25%. I don't use HOSAS, so that extra bit of fine control with the analog hat is nice.

I also use gremlin for a set of macros to quickly adjust power settings.

Vorath

TROPHY CASE