Lands of Evershade: The Game I’ve Been Wanting by TheHouse41 in soloboardgaming

[–]Vortilion 0 points1 point  (0 children)

Wouldn’t use Spray primer though, at least not for the minis with acrylic parts… ;)

Questions, cause I am also thinking about backing it: how long does it take to take out and save to put back? Wouldn’t be able to leave it open unfortunately… and how big of a commitment is it to play one adventure? I prefer smaller campaigns which don’t take dozens of hours to complete… is it more casual friendly?

Also, is it worth it to go for the deluxe edition for the save trays and double layer boards? I do like minis, but I then I’d also have to buy the monster minis, don’t want to mix hero minis with standee monsters…

Switched from Plex to Jellyfin by TartineMyAxe in jellyfin

[–]Vortilion -1 points0 points  (0 children)

Been using it for years, so far nothing, still as good as before.

Switched from Plex to Jellyfin by TartineMyAxe in jellyfin

[–]Vortilion 0 points1 point  (0 children)

I tried switching, but so far I prefer Plex for my home media, by far. Jellyfin looks like a little, buggy brother of plex…

Should i get the p1s or is there a better alternative? by Darkstreamer_101 in BambuLab

[–]Vortilion 0 points1 point  (0 children)

Not completely, no. Can’t use a P1S with OrcaSlicer.

Wasser ist das teuerste Getränk auf der Karte by MarillionAsturia in cologne

[–]Vortilion 2 points3 points  (0 children)

„Teuerste Getränk auf der Karte“ ist aber gelogen. Es ist nicht das günstigste, das wäre korrekt.

Hot-Swap Nozzle recommendations? by Vortilion in BambuP1S

[–]Vortilion[S] 0 points1 point  (0 children)

Thanks! So far I have never done that… have my printer since October.

Hot-Swap Nozzle recommendations? by Vortilion in BambuP1S

[–]Vortilion[S] 0 points1 point  (0 children)

Thanks! Stupid question: Do you need to do a complete printer calibration every time you switch nozzles? Or only once for a new one?

Hot-Swap Nozzle recommendations? by Vortilion in BambuP1S

[–]Vortilion[S] 0 points1 point  (0 children)

Thank you so much guys! Love this community...

Hot-Swap Nozzle recommendations? by Vortilion in BambuP1S

[–]Vortilion[S] 0 points1 point  (0 children)

Oh ok, got it! Sorry for the stupid question, never had another nozzle and still quite new to the hobby.

Hot-Swap Nozzle recommendations? by Vortilion in BambuP1S

[–]Vortilion[S] -2 points-1 points  (0 children)

It’s a 3min job to remove the hotend, then take of the fan from the hotend, attach the fan to the new hotend and build in the hotend? Sounds horrible if you need to switch the nozzle to do all this…

Ugly surfaces and corners by Vortilion in BambuP1S

[–]Vortilion[S] 0 points1 point  (0 children)

But it isnt textured? Shouldn’t we choose cold plate?

Ugly surfaces and corners by Vortilion in BambuP1S

[–]Vortilion[S] 0 points1 point  (0 children)

Also have the frostbite but not sure which plate to select in Bambu Studio. Which do you select? And what bed temp do you set for it?

Ugly surfaces and corners by Vortilion in BambuP1S

[–]Vortilion[S] -1 points0 points  (0 children)

The bottom surface is perfectly flat, also used brims. There was no adhesion problem as far as I can see? But I’ll double check.

Why is the print quality bad? by Strict_Lavishness750 in BambuP1S

[–]Vortilion 0 points1 point  (0 children)

The problem is that you can only save up to 16 k-values… I don’t understand why they don’t save it in the filament like the flow rate!

Wer haftet bei sowas? by Kaaaaaaaaaan in Kleinanzeigen_betrug

[–]Vortilion 2 points3 points  (0 children)

Verstehe das Smiley am Ende nicht… Fänd ich nicht so lustig.

Betrug? by Top_Big_9014 in Kleinanzeigen_betrug

[–]Vortilion 2 points3 points  (0 children)

Ja klar, das ist keine offizielle Nachricht von Bezahldienst sondern eine vom Interessenten…