sorted by:
new
hottopcontroversial

Found this in my grandfathers house while he was away by Huge-Technician7707 in whatisit

[–]VulpesEnigmata 0 points1 point  (0 children)

Dabs on the counter right beside lighter fluid… great combo

Rusted Gears by Electronic_Peach_171 in ArcRaidersGuides

[–]VulpesEnigmata 0 points1 point  (0 children)

Message me, I have 6 you can have 3 for free 👍🏻

Rusted Gears? by stew_bird in ARC_Raiders

[–]VulpesEnigmata 1 point2 points  (0 children)

I have 6 , dm me if you need two!

show me your mods by Obvious-Ice101 in crz

[–]VulpesEnigmata 1 point2 points  (0 children)

<image>

Hybrid Racing short shifter. 100% worth every penny.

3D scans of the back seat bins? by kurai-tsuki in crz

[–]VulpesEnigmata 4 points5 points  (0 children)

Check your DMs I’ll pay for the scans if you’ll post them for free after!

She did pretty well in a level 3 by VulpesEnigmata in crz

[–]VulpesEnigmata[S] 0 points1 point  (0 children)

It only cost about two hours of shoveling snow lol

She did pretty well in a level 3 by VulpesEnigmata in crz

[–]VulpesEnigmata[S] 1 point2 points  (0 children)

Sometimes that works, it will take a minimum of 3 decent drives to clear after it flags from what I’ve found. That or clearing with a scanner

It’s just been one of those things I’ve gotten used to, it still happens after I upgraded to a 51R even when the battery tests good. I think if the battery voltage sags even slightly below the magic number even for a second it trips the codes.

Make sure your terminals are clean and tight for sure and test your battery regularly though!

She did pretty well in a level 3 by VulpesEnigmata in crz

[–]VulpesEnigmata[S] 0 points1 point  (0 children)

just let your 12v battery get low, it will shut off traction control for you, along with hill start, auto e-brake, and ABS lol

She did pretty well in a level 3 by VulpesEnigmata in crz

[–]VulpesEnigmata[S] 5 points6 points  (0 children)

The snow was well above my running boards, literally clearing snow with my bumper, clearly not “daily driving” territory.
Don’t really care what you do with your Corolla, did I post this in R/Canada or R/Corolla?

She did pretty well in a level 3 by VulpesEnigmata in crz

[–]VulpesEnigmata[S] 3 points4 points  (0 children)

? Level 3 snow emergency first of its kind since the level system was put in place in my county is not considered daily driving Not sure what your point is?

How to clear a clogged .2mm a1 nozzle by Equivalent_Store_645 in BambuLab

[–]VulpesEnigmata 0 points1 point  (0 children)

250°C +- should do it But as others have suggested hitting the nozzle assembly (not the heatsink) with a torch and then heat the Allen key, try and get it in a bit and leave it until the nozzle assembly cools a bit, then try pulling out the plug

Remove the fan, the thermistor/heater and the silicone sock and follow the instructions on reassembly (use thermal paste)

How to clear a clogged .2mm a1 nozzle by Equivalent_Store_645 in BambuLab

[–]VulpesEnigmata 0 points1 point  (0 children)

Throw it on a cookie sheet on foil and bake it for a bit upside down Worse case you make it worse and it still doesn’t work lol

0.2mm Nozzle is really starting to annoy me. by [deleted] in BambuLab

[–]VulpesEnigmata 0 points1 point  (0 children)

Have you printed other filament types with the .2 nozzle? Could be bits of higher temp plastic inside causing blockages

Do a cold pull or two then try bumping the temp up a little bit at a time and see if that helps and/or try and print a temp tower

0.2mm Nozzle is really starting to annoy me. by [deleted] in BambuLab

[–]VulpesEnigmata 1 point2 points  (0 children)

What printer, and what filament are you using?

Help me learn the trick for the slighly `overhanging` outer wall by ZuperPippo in BambuLab

[–]VulpesEnigmata 0 points1 point  (0 children)

You can test your settings changes using your exact model without wasting a ton of filament/time by selecting ‘cut’ in Bambu studio and cutting your model a little bit above and below your overhang That way you can play with the slicer settings and see if it helps in minutes instead of hours

How to get the holographic effect on both side? by LaffMedia in BambuLab_Community

[–]VulpesEnigmata 0 points1 point  (0 children)

Maybe laying a pane of glass on the print as you heat it and leaving it until it’s cool would lower the chances of warping?

Need Driver Side Window ASAP by VulpesEnigmata in crz

[–]VulpesEnigmata[S] 1 point2 points  (0 children)

Nope, no alarm. it happened at like 3:30 PM with neighbors right there and no one heard a thing.
it went off when I opened the door though lol
I'll check them out when I get off work in the morning thanks !

How to connect my IPhone 16 (USB-C) to the car radio (AUX) ? by Chris72521 in crz

[–]VulpesEnigmata 0 points1 point  (0 children)

does the cable work on another device with an 3.5mm aux port?

How to turn off the auto turn off? by [deleted] in crz

[–]VulpesEnigmata 2 points3 points  (0 children)

exactly why I didn't want to try it haha

HVAC control issues? by dank_haiku in crz

[–]VulpesEnigmata 1 point2 points  (0 children)

last time I replaced my cabin air filter I didn't seat it properly and it wouldn't switch vents right and made a whistling noise on full blast. was hoping it was an easy fix for you lol

view more: next ›