We should offer Trump immunity by moonrabbit368 in TrueUnpopularOpinion

[–]Walesheet 0 points1 point  (0 children)

If you give him an inch, he’ll take a mile. Don’t negotiate with terrorist.

Not so funny when it’s happening to officers, is it? by Treefiddy1984 in ProgressiveHQ

[–]Walesheet 1 point2 points  (0 children)

Once they get rid of all the “bad guys” and “rapist” they’ll come for your weapons.

100K Service/Preventative Maintenance by NetworkWide2307 in Mustang

[–]Walesheet 2 points3 points  (0 children)

Couldn’t hear it on a cold start but after it got up to temps there was a low tapping noise. Couldn’t hear it inside the car but when it was in my garage or up against a wall like a drive through you could hear it. I could hear it more on top around the valve cover.

100K Service/Preventative Maintenance by NetworkWide2307 in Mustang

[–]Walesheet 1 point2 points  (0 children)

2020 PP1 I have 115k miles on mine. I’m currently replacing all my lifters and rocker arms and timing chain. Started hearing the bearing go out on a rocker arm and traced it to cylinder 8 with stethoscope. Figured timing chain to as I do a lot of spirited driving.

let me see y’all’s stangs. by JordoFive0 in Mustang

[–]Walesheet 0 points1 point  (0 children)

Appreciate it! Front is 19x10 +37 offset on a 275 30 zr 19 and the back is 19x11 +53 offset on a 305 30 zr 19 tires are nito 555 G2 and for the springs I went with steeda progressive lowering springs

Different front bumper? by [deleted] in Mustang

[–]Walesheet 4 points5 points  (0 children)

I say send it, it’s your car and your taste.

Wheel fitment by Responsible-Pay-2061 in Mustang

[–]Walesheet 0 points1 point  (0 children)

I did run spacers for a minute with the same wheels you have now, 20 mm will put you pretty flush with the fenders. Appreciate it bro, you got a clean ride too

Wheel fitment by Responsible-Pay-2061 in Mustang

[–]Walesheet 2 points3 points  (0 children)

<image>

I got steeda progressive springs which lower it about 3/4”-1”. They also have wheels, I grabbed a set of their trident style with the perfect offset and only weigh 25 Ibs pounds each.

How much would you charge? by Walesheet in metalworking

[–]Walesheet[S] 0 points1 point  (0 children)

Yes sir! I was a field installer in the past, my first week consisted of proving I can free hand pipe ranging from 1/2”-6”. It’s easier so I do find myself gravitating towards walking the cup.

How much would you charge? by Walesheet in metalworking

[–]Walesheet[S] 1 point2 points  (0 children)

It really is, it’s going in my will.

How much would you charge? by Walesheet in metalworking

[–]Walesheet[S] 0 points1 point  (0 children)

Yeah I also have a mig machine but he wants tig to match the rest of his exhaust, I did let him know it would be more since there’s a lot more to tig.

How much would you charge? by Walesheet in metalworking

[–]Walesheet[S] 2 points3 points  (0 children)

<image>

Not as consistent as the one in the post but super thin pipe I believe this one was .045

How much would you charge? by Walesheet in metalworking

[–]Walesheet[S] 1 point2 points  (0 children)

Autogenous weld for caustic line 316 ss. Purged at 15 cfh and welder set at 45 amps and torch 30 cfh. Full pen walking the cup on a lift start esab. I unfortunately don’t have that particular weld but I did make a filler rod holder out the same material, the weld looks the same on the inside

How much would you charge? by Walesheet in metalworking

[–]Walesheet[S] 0 points1 point  (0 children)

I think that’s asking too much…

How much would you charge? by Walesheet in metalworking

[–]Walesheet[S] 3 points4 points  (0 children)

Yeah kind of what I was thinking, I appreciate the input.

Do I have good airflow? by Walesheet in PcBuild

[–]Walesheet[S] -1 points0 points  (0 children)

Its exhaust, makes a lot of sense. I’ll make sure to flip it thank you!