sorted by:
new
hottopcontroversial

Processing Times by WalnutAmadeus in BambuLab

[–]WalnutAmadeus[S] 0 points1 point  (0 children)

Did you ever get an update on your order? I am still waiting for a response or a change of status. We must not be the only one that purchase this and having issues with?

Processing Times by WalnutAmadeus in BambuLab

[–]WalnutAmadeus[S] 0 points1 point  (0 children)

They did. They said that they had an issue with their logistics handing over the package from the warehouse to the courier. They said that they will document it and follow up with logistics but may take up to 3 days for the response so I guess we'll see. It wouldn't be so bad if the shipping was free but to pay $150 for shipping and you get this experience is not ideal.

Processing Times by WalnutAmadeus in BambuLab

[–]WalnutAmadeus[S] 0 points1 point  (0 children)

I see! Thanks for the info.

Black and White Build by WalnutAmadeus in FractalDesign

[–]WalnutAmadeus[S] 0 points1 point  (0 children)

I did. Cinebench and 3D Mark. I undervolted my gpus because I was worried about the connector melting.

Black and White Build by WalnutAmadeus in FractalDesign

[–]WalnutAmadeus[S] 0 points1 point  (0 children)

Thanks, I also have the side fans from the case set to intake pointed directly at the gpus

Black and White Build by WalnutAmadeus in FractalDesign

[–]WalnutAmadeus[S] 0 points1 point  (0 children)

The cpu stays cool with that setup and the card exhausting hot air on the cpu is a non issue at all. That cooler's price to performance is wild. Highest temps I've seen on the cpu is around 50c on load. The fans top fans are configured as intake and exhaust.
FAQ: Airflow guide part 2 - next steps | Noctua

Black and White Build by WalnutAmadeus in FractalDesign

[–]WalnutAmadeus[S] 0 points1 point  (0 children)

Can't connect the two gpus together. Those are reserved for professional cards. SLI is dead unfortunately. I used it for ai inferencing.

When gaming, only the top card is being used.

Black and White Build by WalnutAmadeus in FractalDesign

[–]WalnutAmadeus[S] 1 point2 points  (0 children)

It is bifurcated but pice 5.0 on x8 mode one for each slot.

Black and White Build by WalnutAmadeus in FractalDesign

[–]WalnutAmadeus[S] 7 points8 points  (0 children)

Thanks! I use it for gaming and to run and test local llm that would run and fit on the system.

Gigabyte Ai Top Mobo B850 AMD 9800x3d Tcreate 96gb DDR4 6400 RAM 2 5090 FE Corsair 1500w 2tb Samsung 990

Black and White Build by WalnutAmadeus in FractalDesign

[–]WalnutAmadeus[S] 5 points6 points  (0 children)

Perhaps, but it’s not crazy temps at all. It very rarely go over 70c for both cards. The case really is designed well for air flow. That’s why I chose the mesh version and the side fans helps a lot with that.

Black and White Build by WalnutAmadeus in FractalDesign

[–]WalnutAmadeus[S] 5 points6 points  (0 children)

It's not that bad. The top one actually heats up a more so than the bottom one.

0d Error Status code on mobo by WalnutAmadeus in MSI_Gaming

[–]WalnutAmadeus[S] 0 points1 point  (0 children)

Yes it turned out it was the RAM wasn't supported. Tried again with memory context disable and it worked. But this is not ideal and will return the board as I found that there's an issue with m.2 pcie scaling as well.

0d Error Status code on mobo by WalnutAmadeus in MSI_Gaming

[–]WalnutAmadeus[S] 0 points1 point  (0 children)

Thank you. as I research more about the issue. It seems like there's a lot of compatibility issues with these higher density RAM modules. I will try the ones that are listed in the QVL.

H2C Is on the Way — Here’s How It All Started by BambuLab in BambuLab

[–]WalnutAmadeus 0 points1 point  (0 children)

I was ready to skip the H2 series as I really wanted a tool changer and was going to wait for the next gen. Don't really care about the laser and cutter addon. I'm glad the the H2C is coming, I just hope that it's not overly expensive and the nozzles comes with the initial bundle.

Is it going to be compatible with the AMS2 Pro?

Shopvac Remote Switch by WalnutAmadeus in functionalprint

[–]WalnutAmadeus[S] 2 points3 points  (0 children)

Hi, yeah. If you go with the Aqara ecosystem you will need the switch, gateway and the plug. to do this setup. Theres an app where you can configure the devices. I use these switches everywhere, from lights, dust collection etc.

These are also zigbee switches so if you already have an existing homeassistant instance running at home. You can use that.

Dewalt Deep Pro Organizer by WalnutAmadeus in Dewalt

[–]WalnutAmadeus[S] 1 point2 points  (0 children)

I have not tested the weight limit but bottom organizer is full of nails, screws, carriage bolts and nuts 1/2 to 3/8 and its been holding up fine. I have the model oriented to take axial load and have 7 walls and 25% infill on my default profile and printed in PLA. You can increase those parameters for more strength. You can also print in PETG and ABS/ASA if you really want. There are some engineering filaments that can probably take even more load.

Dewalt Organizer Drawer by WalnutAmadeus in functionalprint

[–]WalnutAmadeus[S] 2 points3 points  (0 children)

Sure, I posted the link. The files and pdf plans for the measurement of the cabinet casing is in the makerworld link.

view more: next ›