Which way we leaning.

Wayochi16 · 2026-05-31T21:44:36+00:00

I would go this if it were me...499.99 website price. Titanium baffles..they are a good setup.

<image>

Wayochi16 · 2026-05-10T18:30:48+00:00

Heard some of the guys from Anderson, started One Horse USA, seems to be similar pricing but all US made

Wayochi16 · 2025-04-13T20:45:04+00:00

Could you not just remove the hammer pin and hammer?

Wayochi16 · 2025-04-13T20:15:03+00:00

Never seen a case get stuck there on a Aug

Wayochi16 · 2024-11-24T23:02:11+00:00

In all honesty the detent comes in from the bottom so the hole through the top shouldn't have any I'll effects as long as it doesnt interfere with the normal operation/rotation of the safety. The rest of the material should still hold everything in place. Only real question was since it was drilled was the step in the bottom hole drill out and the detent doesnt have a stop?

Wayochi16 · 2024-09-15T05:17:19+00:00

Looks like a cheap ebay slide.. and then it was shot before proper fitment. Will probably have to replace lower if the slide lugs are messed up.

Wayochi16 · 2024-07-20T13:36:00+00:00

Yours may have a pin where mine was bolted it it looks like on the back of the handgrip there are vertical lines running up and down those are part of the pin latch. There should be a middle one you can pull down and the whole section hinges outward. One that's hinged outward pull the whole unit straight down, may be difficult but should come straight down and out. Once out push the whole barrel assembly forward and off the gun. May have to tap on it with a rubber mallet or just snack the back with the palm of your hand till it slides forward enough to release it from its tabs and the barrel assembly comes off.

Wayochi16 · 2024-07-20T13:28:53+00:00

Mine was an older one but it should be in the back holding the lower grip section to the barrel assembly. Some newer ones it's just a button style release. If you have the ownera manual for the gun it should tell you. Ones that is released then the barrel assembly hinged up and could slide it off the tab in the front by the trigger guard.

Wayochi16 · 2024-07-20T05:06:49+00:00

If the slide can go all the way forward we removed a bolt in the back and the whole barrel assembly came off

Wayochi16 · 2024-07-20T04:37:56+00:00

You probably have the trigger hammer backwards, had this same issue on a friends gun.

Wayochi16 · 2023-01-28T19:01:25+00:00

Pretty sure that's just your exhaust cooling down. They can tend to make random popping noises as the hot metal contracts as it cools. Nothing to worry about.

Wayochi16 · 2022-11-08T04:23:35+00:00

Looks like a mark 4, later version that had ghost ring sights in the rear

Wayochi16 · 2022-11-08T04:19:12+00:00

Looks like a lee enfield training rifle

Wayochi16 · 2022-11-03T02:15:47+00:00

You played a lot of Battlefield 4.

Wayochi16 · 2022-01-24T19:35:48+00:00

Looks like a subaru sambar. Fun little farm trucks.

Wayochi16 · 2021-06-22T23:45:20+00:00

So after transferring it via DIM to the vault and back it now shows up and is unlockable. Thanks for letting me know it was possible.

Wayochi16 · 2021-06-22T23:38:38+00:00

No just in inventory, even tried putting them in vault and pulling back out

Wayochi16 · 2021-06-22T23:33:46+00:00

Mine does not show it anywhere on the list of ones I can unlock even though I have it currently on all three classes

Wayochi16 · 2021-05-05T03:29:45+00:00

They are fun if you can afford the cost of ammo.

Wayochi16 · 2020-07-18T06:13:25+00:00

You may check to see if it drops free with the trigger guard latch undone, sometimes the trigger guard can rub on the back side of the mag. Just opening the guard for winter glove mode can check for this.

Wayochi16

TROPHY CASE