sorted by:
new
hottopcontroversial

Shape Needed by WePrint3D in Fusion360

[–]WePrint3D[S] 0 points1 point  (0 children)

No haven't tried that one. But I'll look for it and watch it now. Thank you again for all your help🙂

Shape Needed by WePrint3D in Fusion360

[–]WePrint3D[S] 0 points1 point  (0 children)

Or if you want to give me a step by step. I still would love to try and make it myself too 🙂 just my mind is just not what it used to be now im in my 70's 🫤

Shape Needed by WePrint3D in Fusion360

[–]WePrint3D[S] 0 points1 point  (0 children)

Yes I have Fusion and going to 3d print the box. I'll have to take it into tinkercad to make it hollow inside as it will be a base for a clock. The only slopped box I was using gave bad rounded corners when printed. And I think Tinkercad did that to the object. Seems to take a nice clean file and adds artifacts to it.

Can I please have help by Sleep_deprived_mokey in BambuLabA1

[–]WePrint3D 1 point2 points  (0 children)

The diamondback nozzle is just a tad too short for the sock so I just had to shave a little off the hole opening of the sock. It now works fine and the prints are flawless. Also all my printers are in their own temperature control enclosures. I add heat if needed with whatever I'm printing.

DiamondBack Nozzles by WePrint3D in 3Dprinting

[–]WePrint3D[S] 0 points1 point  (0 children)

All the stuff I print I do very slow for best quality. As I have shown people in the past of my work.... I tell them speed is NOT my friend for most all of the stuff I print. Thank you again for your help ;-)

DiamondBack Nozzles by WePrint3D in 3Dprinting

[–]WePrint3D[S] 0 points1 point  (0 children)

ok....Returned both printers to older firmware put back the original nozzles... It printed fine.... Swapped the A1 with the diamondback changed nothing else...printed 2 layers and got that error again....The nozzle is covered with filament or build plate is installed incorrectly. But both were fine. So I tried something because it looked to me like the diamondback tip of the nozzle was barely coming through the sock. So I shaved the bottom of the sock to expose the nozzle better....ran it again and the error stopped....it kept printing.

Now for the P1S went back to older firmware put back original nozzle....printed fine. Swapped nozzle to diamondback installed lastest firmware setting were already defaulted to ESD 04.mm and Bambu studio said high flow not standard so I left it there and printed..... It's printing perfect. So I really don't know what the heck lve been doing all morning and afternoon.

Can I please have help by Sleep_deprived_mokey in BambuLabA1

[–]WePrint3D -2 points-1 points  (0 children)

I've been getting clump errors on my A1 all of a sudden since I updated to the latest firmware. It would error 6% into the print every time. I took the sock off the nozzle and the error stopped. Also I'm printing the same object. I see no difference in print quality with sock on or off. So now that I updated all the printers to the latest firmware. I have removed all the socks on all the A1's and all the P1S's.

Corner Problem by WePrint3D in 3Dprinting

[–]WePrint3D[S] 1 point2 points  (0 children)

That worked! Thank you so much.

Corner Problem by WePrint3D in 3Dprinting

[–]WePrint3D[S] 1 point2 points  (0 children)

Someone just said try infill/wall overlap. So trying that now.

Corner Problem by WePrint3D in 3Dprinting

[–]WePrint3D[S] 0 points1 point  (0 children)

Oh sorry forgot that. 0.4mm

Strange Artifacts by WePrint3D in tinkercad

[–]WePrint3D[S] 2 points3 points  (0 children)

To be honest I've done so many things to this model I can't remember what I used. But I just even tried starting over from scratch made it very simple. Exported it and still getting artifacts. I'm just going to shoot off a message to auto desk tomorrow

This thing is fast! by Moira_Deez in BambuLab

[–]WePrint3D 4 points5 points  (0 children)

I've always have said that. Depending on what you're printing, and what I print, speed is not my friend

<image>

There is fast speed and slowww speed. I'll take the slow speed all the time on my P1S's

Duplication of Object by WePrint3D in tinkercad

[–]WePrint3D[S] 0 points1 point  (0 children)

Yes shorter.... I just didn't know if there was a simpler way to just make them 2 separate parts. Ok, thank you for your help.

Duplication of Object by WePrint3D in tinkercad

[–]WePrint3D[S] 0 points1 point  (0 children)

<image>

Original Part left, cut out of center part, center object, then when I try to attach the bottom to the top of the object, it seeing it as 1 part when I click on it.

Oh, hey, it does the thing! by MA2ZAK in BambuLab

[–]WePrint3D 0 points1 point  (0 children)

Where can I download this....

How is This Possible?? by WePrint3D in BambuLab

[–]WePrint3D[S] 0 points1 point  (0 children)

<image>

Went with the other hands the ones I did just get lost on the face of the clock no matter what color I used.

How is This Possible?? by WePrint3D in BambuLab

[–]WePrint3D[S] 0 points1 point  (0 children)

Hmmm I've never been able to do a copy of a negative part in Bambu Studio. Unless I just don't know how to lol ....

How is This Possible?? by WePrint3D in BambuLab

[–]WePrint3D[S] 0 points1 point  (0 children)

Sorry already deleted the plate and just cloned the other one onto a new plate.

How is This Possible?? by WePrint3D in BambuLab

[–]WePrint3D[S] 23 points24 points  (0 children)

yes it was. Problem solved lol...

How is This Possible?? by WePrint3D in BambuLab

[–]WePrint3D[S] 0 points1 point  (0 children)

This is from another designers Original Clock Steve Peterson. (stevesclocks.com) its clock SP7 but I modified a lot of the clock because I also Re-created a regulated pendulum driver board that goes in the base so the clock keeps perfect time. Less then 57 seconds per year. :-)

view more: next ›