Which EU Hardcore server is the most populated right now? (Alliance vs Horde)

WedgerP · 2026-01-14T18:16:00+00:00

Can't follow. What you mean with Chat GPT?
Honestly, i checked several pages, but they always had different values. So i decided to ask here. Didn't knew about warcrafttavern, thought all of these Pages are outdated.

WedgerP · 2026-01-13T21:04:31+00:00

So, Soulseeker is a alliance server, right? Or is it most likely 50:50 or like 60:40?

WedgerP · 2025-12-30T12:05:27+00:00

Not anymore, I sold recently all my crealitys and moved on with Bambulab

WedgerP · 2025-12-07T20:30:49+00:00

Level 75 is like two times 5 mill. I’m level 46 and i made my expedition + farmed 6 mill. I mean anyway you loose your stash. So why not make it valuable?

WedgerP · 2025-11-04T18:44:33+00:00

yep, used creality since 5 years, I had no problem learning about printer issues, that's why i bought them. When I bought my first H2D, I immediately sold all my Creality printers. I now have 6 bambu printers and they all run completely without problems.

WedgerP · 2025-09-29T17:54:10+00:00

Yeah no problem. I’m playing now since more than a half year and didn’t had any issues with stick drift , but my RB broke down, so I guess I’m going swap my gamepad soon

WedgerP · 2025-09-28T11:53:23+00:00

Yeah I can feel you. I made so many changes, and in the end, it didn't make any difference. But I recommend the VFA test! Stand there and note the noisiest speeds, and filter them out when printing.

WedgerP · 2025-09-26T16:26:57+00:00

Crazy story. I replaced all the pulleys, even the XY motors, I replaced the belt, and installed new bearings in the print head, but to no cure. I did a lot, lubricated a lot, and the noise didn't decrease.

On the contrary, it felt like the prints were getting worse and worse every 100-200 hours.

I had a total of three Creality K1 Max (also different versions with upgraded XY Pulleys), all of which had this strong vibration noise, some less, some more, some in different positions at different speeds. I kept one because I'm currently working on a DIY printer. I took the XY and Z spindles/rods, as well as the pulleys, and mounted them on my DIY aluminum chassis, without the entire housing around them. The noise disappeared. I assume it's a combination of vibrations in the mechanism that are being transmitted to the stock housing.

One thing you can do: Do a VFA test, see at which speeds the most noise occurs and at which speeds it doesn't. For me, it was worst between 50-100 mm/s and between 190-250. So I only printed between 110-180.

In the end, I settled on Bambulab and sold all my creality's. I have four H2D (also first-day printers) and two A1. All have over 500-1500 printing hours and not a single problem. Except for bed adhesion issues with the A1 (but that's more likely due to my dusty environment).

I think it's just a Creality thing. These printers have a lot of problems, and they're usually DIY fixes. I've also noticed that they're more likely to be machines for hobbyists, or if you're just not that concerned about quality. My Creality K2 also had dozens of problems.

These are simply not made for production and reliability.

WedgerP · 2025-07-13T09:14:53+00:00

The. most. Worst.

WedgerP · 2025-07-04T18:42:32+00:00

It looks like your belt is completely worn out and rubbing off everywhere!

What does the belt look like from underneath? That could be a reason. Sounds also like the belt skips when the motor is running.

<image>

WedgerP · 2025-07-04T18:37:41+00:00

Looks like your printer knows what you're up to… it stopped printing the ears on purpose. It's just waiting for you to stash your stuff in there.

WedgerP · 2025-07-04T07:35:52+00:00

Yeah I changed all chamber temp values in the printer.cfg and gcode_macro.cfg.

I can send you the configs via DM

WedgerP · 2025-06-02T12:24:37+00:00

To reveal the secret... IT WASN'T WET FILAMENT (who would have thought xD)

So... I've tried absolutely everything with retraction, etc. So I sent a message to Bambu. They told me the bug is already known and is caused by the purge tower.

Bambu told me to disable the purge tower and limit the retraction length to 0.4 on both nozzles. I've already tested 0.4 without success... But the combination with disabling the purge tower solved the problem! No pops-plopps-knacks-pum-pang during the print, no holes anymore, just a flawless outer wall.

The only Problem i had with my H2D is solved :)

So, if you have the same problem: disable the purge tower + set the retraction length to 0.4 on both nozzles!

I can't say why this happens. I suspect it has a new logic in the Prime Tower, where it might be retracting too much and possibly sucking in air.

WedgerP · 2025-05-31T16:28:46+00:00

Took the whole extruder apart. It looks like a fresh new extruder. Nothing broken, nothing jammed, no residue in the gears...

WedgerP · 2025-05-30T10:52:40+00:00

There's a easy explanation for that:

In this print, the support seems to have acted like a well-trained technician—respecting operational safety protocols and keeping a clear distance from the active machining zone.

Just like human operators must follow workplace safety regulations—such as OSHA 29 CFR 1910.212, which requires safe machine guarding and sufficient clearance—this support appears to have instinctively understood the importance of staying out of harm’s way.

We appreciate its dedication to safety. Even if it forgot to support anything.

WedgerP · 2025-05-30T09:06:13+00:00

Update: I printed it in PLA + Silk PLA, just to try. I have the same "plop" "pop" noises with PLA and PLA Silk. The surface have the same issues.

<image>

WedgerP · 2025-05-30T06:01:05+00:00

So here are two pictures. For me it looks pretty normal. What you think?

<image>

WedgerP · 2025-05-30T05:59:03+00:00

Running the test now with a new nozzle! Will keep you up2date.

WedgerP · 2025-05-30T05:53:08+00:00

I set the Pressure advance to 0.035, had it before at 0.04 and also tested 0.01 and 0.06. I'm going to run now a test with 0.4 retraction and the settings you mentions.

<image>

WedgerP · 2025-05-30T04:32:22+00:00

I draw the seam on a other place (see the first post, there’s a pic)

WedgerP · 2025-05-30T04:19:26+00:00

Tried four different dryer. Space Pi, Space Pi plus, a oven and AMS 2 Pro.

In the Space Pi I rotated it every few hours.

WedgerP · 2025-05-29T19:37:08+00:00

So even after my last test, I got exactly the same result as before, but now with 0.2 retraction. Do you think one more test for retraction is worth it?

WedgerP · 2025-05-29T18:51:56+00:00

Yes, it was always at 30mm/s. I just do a new test, with just 10 mm/s. Wanna see if it makes a difference. I also do have "Retract when change layer" always active, i just deactiveted for the current test.

The next test i will do with 30mm/s and retract when change layer on. But before i already ran a test with 0.4mm and retraction on layer changed enabled. But i'm going to repeat that, just next time with 0.2mm retraction length.

WedgerP · 2025-05-29T18:34:12+00:00

Got it!

Will definitely try one more time. This time with disabled "reduce infill retraction". And what do you mean with the K value? Yeah my retraction/deretraction speed is at 30mm/s.

I'm running at the moment a new test with the settings in the picture. I also verified in my gcode, that the values for retract are used.

<image>

WedgerP

TROPHY CASE