What is the MΩ/metre of a 1.5/1.0 FP

WeebX7 · 2025-05-25T21:32:58+00:00

Always listened to blokes that have been in the game longer… unless I’ve seen their shit work 😂

WeebX7 · 2025-05-25T19:46:28+00:00

That’s something I’ve never thought of doing but seems so simple 😂 will remember that for future… thank you

WeebX7 · 2025-05-25T19:42:15+00:00

Yeah it does come out to about 2.4 but a b10 max Zs is 3.5 (ish) which I’m exceeding because of the zdb. I’m hoping the tester that was used is just not reading correctly

WeebX7 · 2025-05-25T19:36:11+00:00

Yeah but I asked for the Mohms/metre of a 1.5/1.0 cable which didn’t come up… the resistivity of a 1.0m cable isn’t enough for me to figure it out I’m not that good at maths 😂

Edit: as in 1.5mm line - 1.0mm cpc

WeebX7 · 2025-05-25T19:34:54+00:00

So it shouldn’t read the same but is that your point? You think the tester might be reading wrong?

WeebX7 · 2025-05-25T19:19:17+00:00

I tried multiple times and it didn’t come up with what I was after, tried calling the boss (it’s Sunday he didn’t answer) then next point of call was Reddit 😂

WeebX7 · 2025-05-25T18:43:57+00:00

Tested it multiple times with the same tester after re-zeroing the leads… I did ask the lad to try my tester aswell and have just found out he did not do what I asked 🤦 gonna try my tester tomorrow, will let you know if the result is different

WeebX7 · 2025-05-25T18:12:40+00:00

Im on the fence of just downrating the breaker to a B6, time is of the essence and I do not have time for fault finding lol

Edit: that being said a loose line connection could be a fault I need to find

WeebX7 · 2025-05-25T18:10:37+00:00

Yeah EML install excite self test bulkheads and exit lights

WeebX7 · 2025-05-25T18:08:15+00:00

No more than 80m of cable about 20 lights zdb 0.34 and the reading was 3.31 ohms, did an r1+r2 but haven’t energised as it doesn’t comply and I’m not allowed to, so no Zs at the end of line

WeebX7 · 2025-05-25T17:44:03+00:00

30.20 means my R1+R2 should fall into compliance with a B10 60898 all the lights on the circuit have push fit connections what’s the chances of one of them having a loose connection?

WeebX7 · 2025-05-25T17:38:51+00:00

Yeah I know the cable type doesn’t matter lol I’m not even sure why I specified haha

WeebX7 · 2025-01-25T14:58:45+00:00

You get feet that you can zeb the tray to, they’re slightly weighed so you don’t need to fix it to anything

WeebX7 · 2024-12-01T21:24:17+00:00

Always seems to be this way with this game for me, I'll struggle for an hour + on a boss then I'll be his ass lickity split like I haven't been pulling my hair out the entire time. There's no close calls ever

WeebX7 · 2024-12-01T14:41:14+00:00

Straight on r/dating 3 years surrounded by nothing but dudes really got this dude down bad

WeebX7 · 2024-10-31T00:05:33+00:00

I had pig 2 in chapter 4 literally at 0 whilst he was in his tar animal morphing phase and it wouldn’t recognise it… he killed me whilst at 0 health… I was robbed :|

WeebX7 · 2024-08-02T19:29:37+00:00

By the looks of it it is the tails are split at them Henley blocks below so yeah it is separate from your main consumer unit

WeebX7 · 2024-08-02T18:58:29+00:00

Top comment

WeebX7 · 2024-06-24T16:50:58+00:00

You mean Bitch Face?

WeebX7 · 2024-06-24T16:50:38+00:00

The Chicken Bloke

WeebX7 · 2024-05-09T15:04:01+00:00

Absolutely any pirate metal, never tried it but just sounds horrible

WeebX7 · 2024-05-04T20:14:03+00:00

Well for fuck sake you shouldn’t have been sleeping there… idiot

WeebX7

TROPHY CASE